Com-Fab

This kit contains all of the materials necessary to mount a bunk on one of our canoe or kayak trailers. The kit contains:

2 – 3/8”-16 x 2.06” x 2.88” Zinc U-Bolt
2 – 4" x 1" x .25" Zinc Flat Plate
2 – Galvanized Angular Swivel Bracket
4 – 3/8"-16 Serrated Zinc Flange Nut

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

General

Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly w/ Bearings, Seal, Amp, and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98" 

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- 12 Position Castle Nut

- Cotter Pin

MODEL: CFAXLE-HUB5BLT(1350-B)

Used on

General

Black Powder Coated Axle Mounting Kit

This kit is used to mount Black Powder Coated Axles to Black Powder Coated PWT Trailer models.

Materials Include: 

2 - 1/2" x 3" Zinc Hex Head Bolt

2 - 1/2"-13 Zinc Flange Top Lock Nut

MODEL: CFAXLEKIT-MOUNT(Z)

Used on

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

Brass Banjo Brake Fitting Base

This item is used in conjunction with a banjo fitting bolt, a Black O-Ring and a Copper Washer for brake line quick connect.

For use with:

– Copper Banjo Fitting Washer

TIE DOWN MODEL: #11348

MODEL: CFBRKE-BASEBANJO

General

Brass Banjo Fitting Bolt for (Round) Banjo-fitted Brake Lines

This item is used in conjunction with 64" Grey Flex Banjo-Banjo Brake Lines, O-Rings and Copper Banjo Fitting Washers to connect Aluminum E-Coat Caliber Assemblies on all tandem axle pontoon trailer models.

For use with: 

– Copper Banjo Fitting Washer

MODEL: CFBRKE-BLTBANJO(RD)

Used on

General

Company Graphic for Double PWT and Pontoon Trailers

This graphic sticks to the side of all Double PWT and Pontoon Boat Trailer models.

Dimensions: 30.25" x 3"

MODEL: CFGRAPHIC-(4X2)

Used on

General

Company Graphic for Single PWT and Jon Boat Trailers

This graphic sticks to the side of all Single PWT, Jon Boat, and PWT-2212 trailer models. 

Dimensions: 19.75" x 2"

MODEL: CFGRAPHIC-(3X1.5)

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

Dry Launch 60″ Red Triple Light Bar

This light bar can be mounted to all Double PWT, and Pontoon Boat Trailer models. It is secured with two 12 x 3/4″ Zinc Hex Washer Head Tek #3 Screws.

MODEL: CFLIGHTBAR-60

Optional for

General

Dry Launch Amber Side Marker Light w/ 10" of Wire

This item is a Dry Launch 203 Series with a snap out bulb slide. You can change the bulb without tools, and mount it with a single stud. It can be used as a Side Marker Light for the tongue of all Pontoon Boat Trailer models.

MODEL: CFLIGHTSDMRKR-10

Optional for

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6.75"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6.75"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Dutton-Lainson 600 lb Winch Handle

This ergonomic handle attaches to a Dutton-Lainson 600 lb Capacity Crank Winch with 1/2" Nylock Nut.

DUTTON-LAINSON MODEL: #70304

MODEL: CFWNCHHANDLE-DL600

Used on

General

Flat Pontoon Bunk Bracket #44879

Length: 9.02"

Base Length: 8.38"

Width: 3"

Height: 5.25"

Optional for

General

Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98"

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- Cotter Pin

TIEDOWN MODEL: #46205X

MODEL: CFAXLE-HUB5BLT(1350-G)

Used on

General

Axle Equalizer

Two of these axle equalizers are part of the Pontoon Boat Trailer Tandem Axle Mounting Kit used to mount 3-Leaf Double Eye Springs to frames on all Tandem Axle Setups for Pontoon Boat Trailers

MODEL: CFAXLE-EQUALIZER

Used on

General

Galvanized Axle Mounting Kit

This kit is used to mount Complete Galvanized Axles to all PWT, and Jon Boat Trailer models.

Materials Include: 

2 - 1/2" x 3" Galvanized Hex Head Bolt

2 - 1/2"-13 Galvanized Tri-Lock Nuts

MODEL: CFAXLEMNTKITG

Used on

General

Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models

This fender is mounted to every Jon Boat Trailer, Kayak/Canoe Trailer and PWT-2212G models with a Jon Boat Trailer Fender Mounting Kit, and fits a 4.80 x 12″ C Load Range Galvanized Tire & Wheel.

MODEL: CFFNDRJBT/2212G

Used on

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

Galvanized Single Axle Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This fender with welded on spring hangers is mounted to a Pontoon Boat Trailer using a 2213G - Fender Mounting Kit, and typically uses a ST175/80R13 D Load Range 13″ Galv. Tire & Wheel. A 3500 lb Hydraulic Disc Brake Trailer Axle, or a 2900 lb Idler Trailer Axles is then mounted to the fender hangers using a Pontoon Boat Trailer Single Axle Mounting Kit.

MODEL: CFFNDRPT(SA-G)

Used on

General

Galvanized Tie Plate Kit for 1.5" Square Trailer Axles

This kit is used to mount springs to Galvanized 1.5" Square Trailer Axles. The kit is a part of the 1500 lb Galvanized Trailer Axle used on every PWT-1000G, and PWT-1100G trailer model. It is also part of the 1500 lb Extended Galvanized Trailer Axle used on both PWT-2212 trailer models.

Materials Include:

2 - Galvanized Axle Tie Plate for 1.5" Square Trailer Axle

4 - 3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt

8 - 3/8"-16 Galvanized Tri-Lock Nut

8 - 3/8" Galvanized Lock Washer

MODEL: CFAXLEKIT-SPRNGMNT(1.5K-G)

Used on

General

BATIE190G Galvanized Tie Plate Kit for 2" Square Trailer Axle

This kit is used to mount springs to 2" Square Trailer Axles. This kit is part of the 2500 lb Galvanized Trailer Axle used on PWT-2213G, and PWT-2214G trailer models.

Materials Include:

2 - BATIE190G Galvanized Tie Plate for 2" Square Axle Tubing

4 - 1/2"-13 x 2.06" x 4.31" Galvanized U-Bolt

8 - 1/2″-13 Galvanized Tri-Lock Nut

MODEL: CFAXLEKIT-SPRNGMNT(2.5K-G)

Used on