2 Capacity Canoe/Kayak Conversion Kit
$320.00
Universal canoe/kayak trailer conversion kit for up to 2 canoes or 2 kayaks without plastic protective covering.
One size fits all trailer kit:
- Designed to hold 2 kayak/canoes
- Adjustable crossbeam placement to fit a wide range of needs and preferences
- Fits on 1.5", 2", 3" rectangular and/or square tubing where applicable
- 2x2x11 gauge upright bracing for universal fit
- 2x2x14 gauge cross brace with stability slides, preventing side-to-side movement and increase stability (Optional)
This is a conversion kit only and requires a trailer to mount.
Kayak Setup - CFKIT-KAY(2)
- 2x 24" Uprights
- 2x 60" Crossbeams with Strap Assist and End Caps
- 4x Zinc U Bolts with Washer and Nut for Adjusting and Securing Crossbeams
- 4x Galvanized U Bolts with Washer and Nut for Securing Uprights to Trailer *
Canoe Setup - CFKIT-CAN(2)
- 2x 24" Uprights
- 2x 80" Crossbeams with Strap Assist and End Caps
- 4x Zinc U Bolts with Washer and Nut for Adjusting and Securing Crossbeams
- 4x Galvanized U Bolts with Washer and Nut for Securing Uprights to Trailer *
* The tubing size of the trailer will determine which U Bolts will be needed to secure the uprights to the frame.
You might also like
Galvanized Side Mount Spare Tire Carrier
$29.99
Brand Com-Fab
Installation Instructions:
1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.
2. Slide U-bolt around the frame and through the holes in tire carrier.
3. Mount with flat washers, lock washers and nuts provided.
4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.
5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.
6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.
7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.
TecNiq-T86 7 Function 6" LED Tail Light (Passenger Side)
$15.99
Brand Com-Fab
General
TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail
- These are optional for all Trailer Models.
- Multi-Function 6" Box Tail Light
- Urethane Potting w/ Guaranteed Circuit Board Protection
- Dust and water proof with hermetic seal
- Durable impact resistant lens
- Meets all FMVSS 108 requirements for narrow and wide vehicles
- Reliable performance over 100,000 hours
- Fits standard mounting as a direct replacement
- Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
Rear Reflector, and License Plate Light (Left)
Includes two 7/16" bolts w/ nuts for mounting.
MODEL: CFLIGHTREAR(R)-LED(TEC)
Used on
ALL COM-FAB TRAILER MODELS
TecNiq-T86 8 Function 6" LED Tail Light (Driver Side)
$16.99
Brand Com-Fab
General
TecNiq-T86 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.
-
Multi-Function 6" box tail light
-
Urethane Potting w/ Guaranteed Circuit Board Protection
-
Dust and water proof with hermetic seal
-
Durable impact resistant lens
-
Meets all FMVSS 108 requirements for narrow and wide vehicles
-
Reliable performance over 100,000 hours
-
Fits standard mounting as a direct replacement
-
Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
Rear Reflector, and License Plate Light (Left)
Includes two 7/16" bolts w/ nuts for mounting.
MODEL: CFLIGHTREAR(L)-LED(TEC)
Used on
ALL COM-FAB TRAILER MODELS
1200 lb Side Crank Swivel Jack
$52.45 $45.99
Brand Com-Fab
General
1200 lb Side Crank Swivel Jack
This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.
MAXIMUM CAPACITY: 1200LB
PACIDIC RIM MODEL: MJ-1200B
MODEL: CFJACKSIDE
Used on
JBT-900
JBT-1400
JBT-1600
JBT-1600 ‘RIVER HAWK’
PT-1400 'MiniToon'
PT-1618
PT-1820
PT-2022
