PWT-2214G Parts

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

12 Position Castle Nut

This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.

TIE DOWN MODEL: #10634

MODEL: CFAXLE-NUT(CASTLE-L)

Used on

General

1-1/16" L44649 Bearings

These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs

UNIVERSAL MODEL: L44649

TIE DOWN MODEL: #11054

MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER

Used on

ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS

General

Side Crank Swivel Jack Mounting Kit

This kit contains all of the  parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models

MODEL: CFJACK-MNTKIT

Used on

ALL COM-FAB TRAILER MODELS

General

2213/4G - Fender Mounting Kit

This kit contains all of the requisite materials needed to mount a Galvanized Fender 13" Tire onto 2213G, 2214G, and Pre-2019 Single Axle Pontoon Boat Trailer models.

Materials Include:

2 – 3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

2 – 6" x 1.5" x 1.25" Galvanized Flat Plate

4 – 3/8″ Galvanized Tri-Lock Hex Nuts

MODEL: CFFNDRKITG-2213

Used on

General

21' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH21

Used on

JBT-1600 ‘RIVER HAWK’

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

8.25" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes and 3.5" Hole Centers - Shackle Link

This item is part of the 2213G - Bunk Board Mounting Kit used to mount Bunk Boards onto PWT-2213G, and PWT-2214G trailer models.

MODEL: CFFLTSTRPBUNK(DBL)G

Used on

General

3/8″-16 x 3.06" x 4.5″ Galvanized U-Bolt

This item is part of these kits:

- Galvanized Winch Assembly Mounting Kit

- Jon Boat Trailer Bow Support Bunk Mounting Kit

MODEL: CFUBLT3/8X4.5G

Used on

General

2500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 83" x 2" x 2" x 3/16" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 5-Leaf Slipper Springs (1,250 lb)

1 - BATIE190G Tie Plate Kit

This item is mounted to the PWT-2213G, and PWT-2214G trailer models with a Galvanized Axle Mounting Kit.

MODEL: CFAXLE2500G

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 2500 lb

Hub Face: 93.5"

Spring Center: 83"

Overall Length: 98.5

Bearing Size: 1-1/16"

Used on

General

Rhino Kote Galvanizing Graphic (4.5" x 3.5")

Dimensions: 4.5" x 3.5" 

MODEL: CFGRAPHIC-RHINOKOTE (4X3)

Used on

General

Company Graphic for Double PWT and Pontoon Trailers

This graphic sticks to the side of all Double PWT and Pontoon Boat Trailer models.

Dimensions: 30.25" x 3"

MODEL: CFGRAPHIC-(4X2)

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

ST175/80R13 D Load Range 13″ Galvanized Tire & Wheel 65 psi

This item is used on our PT-2426, and PT-2628 Trailer Models, but is also an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFT175DLRD-G

Used on

Upgrade for

General

Galvanized Winch Assembly Mounting Kit

This kit contains all of the requisite materials needed to mount a Galvanized Winch Assembly onto all Galvanized PWT trailer models.

Materials Include:

2 – 3/8″ x 3.06" x 4.5″ Galvanized U-Bolt

2 – 5" x 1.25" x .25" Galvanized Flat Plate

4 – 3/8″ Galvanized USS Flat Washer

4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts

MODEL: CFWNCHKITG

Used on

General

3" Poly Bow Roller Assembly

This is a section of the Winch Poly Bow Roller Assembly.

Materials Include:

1 – 3″ Poly Bow Roller 
2 – 3″ Poly Bow Roller Bell End
1 – 1/2″-13 x 4.5″ Zinc Bolt
2 – 1/2″ Zinc Flat Washer
1 – 1/2″-13 Top Lock Nut

MODEL: CFASSM-POLYRLR(3)

Used on

General

Black Marine Carpet 10.25" Width

$2/ft in 100 ft rolls

- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.

If you are purchasing this carpet it needs to be a foot longer than the board itself.

This carpet comes in these specific sizes as well:

- 5 ft Bunk Board Black Marine Carpet

- 6 ft Bunk Board Black Marine Carpet

- 7 ft Bunk Board Black Marine Carpet

MODEL: CFBNKCOVER-CARPET(10.25)

Used on

Optional for

General

6" x 1.5" x .25" Galvanized Flat Plate w/ 2 7/16" Holes and 4.5" Hole Centers - Shackle Link

- This item is part of the 2213G - Fender Mounting Kit used to mount Fenders to PWT-2213G, and PWT-2214G Trailer models.

MODEL: CFFLTSTRPFNDR(DBL)G

Used on

General

3/8″-16 x 1″ Zinc Hex Head Cap Bolt

This item is used with 3/8"-16 Serrated Zinc Flange Nuts to mount all crank winch models onto every type of winch post. It is also part of the 2213B - Bunk Mounting Kit used to mount bunks onto PWT-2213B, and PWT-2214B trailer models. 

MODEL: CFBLT3/8X1Z

Used on

ALL COM-FAB TRAILER MODELS

General

2″ x 4″ x 7′ Black Marine Carpeted Bunk Board

These are used for all PWT-1100, and PWT-2214 trailer models.

1000B - Bunk Mounting Kit

1000G - Bunk Mounting Kit

2213B - Bunk Mounting Kit

2213G - Bunk Mounting Kit

MODEL: CFBUNKBRDC-7FT

Used on

General

32″ Galvanized Winch Post

- This item is part of the 32″ Galvanized Winch Assembly which is mounted to the PWT-2213G, and PWT-2214G trailer models.

- This item is part of the 32" Galvanized Jon Boat Trailer Winch Assembly which is mounted every Jon Boat Trailer model.

MODEL: CFWNCHPOST32-G

Used on

General

Dutton-Lainson 600 lb Winch Handle

This ergonomic handle attaches to a Dutton-Lainson 600 lb Capacity Crank Winch with 1/2" Nylock Nut.

DUTTON-LAINSON MODEL: #70304

MODEL: CFWNCHHANDLE-DL600

Used on

General

3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

This item is part of the 2213G - Fender Mounting Kit used to mount fenders to PWT-2213G, PWT-2214G, and all Pontoon Boat Trailer models.

MODEL: CFUBLT3/8X3.00G

Used on

General

2213/4G - Galvanized Fender

This fender is mounted to a PWT-2213G, or PWT-2214G trailer model using a 2213G - Fender Mounting Kit, and fits an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

MODEL: CFFNDR2213

Used on