PWT-2214G Parts

General

Dutton-Lainson 600 lb Winch Handle

This ergonomic handle attaches to a Dutton-Lainson 600 lb Capacity Crank Winch with 1/2" Nylock Nut.

DUTTON-LAINSON MODEL: #70304

MODEL: CFWNCHHANDLE-DL600

Used on

General

3″ Amber Poly Bow Roller Bell End

This item is used as part of every Winch Assembly mounted on every PWT, and Jon Boat Trailer model.

This item is part of these assemblies:

- 3" Poly Bow Roller Assembly

- Winch Poly Bow Roller Assembly

TIE DOWN MODEL: #48654

MODEL: CFPOLYEBELL-3

Used on

General

3″ Amber Poly Bow Roller 

This item is used as part of every Winch Assembly mounted on every PWT, and Jon Boat Trailer model.

This item is part of these assemblies:

- 3" Poly Bow Roller Assembly

- Winch Poly Bow Roller Assembly

TIE DOWN MODEL: #48653

MODEL: CFPOLYBOWRLR-3

Used on:

General

3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

This item is part of the 2213G - Fender Mounting Kit used to mount fenders to PWT-2213G, PWT-2214G, and all Pontoon Boat Trailer models.

MODEL: CFUBLT3/8X3.00G

Used on

General

2213/4G - Galvanized Fender

This fender is mounted to a PWT-2213G, or PWT-2214G trailer model using a 2213G - Fender Mounting Kit, and fits an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

MODEL: CFFNDR2213

Used on

General

TecNiq-T86-L 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.

• Multi-Function 6" box tail light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(L)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

3/16" S-Hook with Latch Trailer Safety Chain - 48"

48" 2000 LB safety chain with 3/16 in S-Hooks and latch

MODEL: CFSFTYCHN

Used On

General

Weld Aid B-100 Brite Zinc Aerosol Spray Can

This product is used to touch up, and prevent rust and corrosion on all of our galvanized items for sale. The spray is 69% Zinc Metal ensuring that it matches the shine of any and all Hot-Dipped Galvanized Steel. It has a special no clog nozzle, and can cover up to 40 sq feet of steel. This item meets ASTM-A780 requirements for corrosion protection.

Read the Safety Instructions carefully before use of this item.

https://weldaid.com/wp-content/uploads/2018/11/1008302E.pdf

Specifications

Part No: B-100

UPC: 731592100013

Volume: 12.5 oz Primer

Used On

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

TecNiq Part No. S14-RRS1-1

MODEL: CFLIGHTSDMRKR-LED(TEC-R24)

Used on 

General

TecNiq Red LED V-Shaped Light Bar w/ 58" Lead

• Used on all Double PWT Trailer models.
• Screws included with purchase
• Fully submersible LED Identification bar
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Available in colored or clear impact resistant lens
• IP68 rating while exceeding FMVSS 108 standards
• Reliable performance over 100,000 hours

MODEL: CFLIGHTBAR-LED(V-TEC)

Used On

2″ x 8″ x 10′ Black Marine Carpeted Center Walk Board

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

This item is used for all PWT-2213 trailer models. It is mounted to the center of the trailer frame with six 5/8″-16 x 1-1/2″ Galvanized Hex Head Lag Screws.

MODEL: CFWALKBRDC-10FT

Used on

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

10 ft Walk Board Black Marine Carpet

Protective carpeting for the 2″ x 8″ x 10′ Black Marine Carpeted Center Walk Board used on all of our Double PWC Trailer Models.

11 ft by 14.4 in to fully cover the walk board

Used on

General

Triple Lip Grease Seal - 1.25" I.D. - 1.98"

This seal is part of our Galvanized 5-Bolt Hub Assembly, and our Black Powder Coated 5-Bolt Hub Assembly. This rubber coated seal fits Tiedown Bearings 44643, and 44649

TIEDOWN MODEL: 1252555UC

MODEL: CFAXLE-SEAL(TRIPLE-1.25)

Used on

General

ST175/80R13 13" D Load Range 545 Hole Pattern T07/BM Black Machined V-Spoke Aluminum Radial Tire & Wheel - Kenda/Loadstar, 65 psi

This item is an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFTST175RLRD-VSPOKE

Upgrade for

General

10 ft Walk Board Black Marine Carpet

Protective carpeting for the 2″ x 8″ x 10′ Black Marine Carpeted Center Walk Board used on all of our Double PWC Trailer Models.

$2.25/ft in 100 ft rolls

If you are purchasing this carpet it needs to be a foot longer than the board itself.

Used on

General

Chem Star Bright Finish Zinc Galvanized Spray 16 oz.

This product is used to touch up, and prevent rust and corrosion on all of our galvanized items for sale. The spray is 66% Pure Zinc Metal ensuring that it matches the shine of any and all Hot-Dipped Galvanized Steel. This item meets ASTM-A780 requirements for corrosion protection. This product has a self-healing feature. 

Read the Safety Instructions carefully before use of this item.

https://3741134.app.netsuite.com/core/media/media.nl?id=6095146&c=3741134&h=JEfDoKJfRbMndLebOzYz9EuVV_mDUXXFpBp1te2l5HhIL6aw&_xt=.pdf

Specifications

Part No: 160841

UPC: 843088134669

Volume: 16 oz 

Used On

General

RAM 1500LB Side Crank Swivel Jack

• RAM swivel marine tongue jack for boat and other trailer applications
• 1,500 lb. capacity
• 24-3/4" maximum tongue height
• Side wind handle with extra heavy screw drive and ergonomic handle grip
• Heavy duty polypropylene 8" diameter slotted wheel resists flat spots and cold weather cracking
• Zinc plated finish for additional rust resistance and longer life
• Easily swivels up for towing or down for stowing and locks in place in either position
• Reinforced wheel bracket for additional strength
• Includes all necessary bolt-on mounting hardware
  

MODEL: CFJACKSIDE-1500(RAM)

Used On

PT-/TT-2224
PT-/TT-2426

General

PacRim/RAM 1500LB Side Swivel Jack w/ Dual 6IN Caster Wheels

This item fits 3″ x 4" - 5“ tongues. Mounting Hardware included.

MAXIMUM CAPACITY: 1500LB

PACIFIC TRAILER PRODUCTS/RAM MODEL: 

MODEL: CFJACKSIDE-1500(DWL-RAM)

Used on

PT-/TT-2628
PT-/TT-2830

General

1/2" x 2.06" x 4.31" Galvanized U-Bolt