Parts

General

Smooth Gloss Bengal Black Touch Up Pen

This item is used to touch up all of our Black Powder Coated Trailers, Fenders, and Winch Assemblies for sale. It is specifically designed for our trailers, and is an exact match finish. The instructions for use are clearly labeled on the back of the pen.

Specifications

Net Weight: 3.5 oz/9 ml

Exact Match Finish - Industrial. Product Contains less than 88% VOC/2.05 MIR

Contains: Acetone, Xylene, Toluene, and Petroleum Distillates.

DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR.

VAPORS MAY CAUSE FLASH FIRE.

VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, AND NOSE IRRITATION. 

NOTICE: Reports have associated repeated, and prolonged occupational overexposure to solvents with permanent brain, and nervous system damage. Intentional misuse by deliberately concentrating, and inhaling the contents may be harmful or fatal. WARNING! This product contains a chemical known to the state to California to cause cancer and birth defects or other reproductive harm. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120 Degrees Fahrenheit. Vapors may ignite explosively. Keep away from heat, sparks, and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe dust, vapors, or spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA approved) or leave the area. Close container after each use. Avoid contact with eyes, skin, and clothing. First Aid: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

Instructions

PREPARATION: Surface should be clean, dry, and free of wax, oil, rust, loose paint, etc. WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

DIRECTIONS: Shake well to get best color match. 

KEEP OUT OF THE REACH OF CHILDREN.

General

1 Inch Flat Spindle Washer - "ID" Washer

This item is used to help secure Hubs to Axle Spindles on all of our JBT, PWT & KCT Models. It is placed in between the 12 Position Castle Nut w/Cotter Pin and the hub's outer-facing bearing in the Hub Assembly on the Axle Spindle. 

12 Position Castle Nut

5/32" x 2" Zinc Cotter Pin for Axle Spindle

Axle Spindle

Galvanized 5-Bolt Hub Assembly

Black Powder Coated 5-Bolt Hub Assembly

MODEL: CFAXLE-WSHR(SPINDLE)

MPN: 005-10520

Used on

ALL COM-FAB TRAILER MODELS

General

Heavy Duty Pontoon Bunk Bracket #43747

This item is optional for all Pontoon Boat Trailer models. It fits 2' x 4' and 2' x 6' boards.

Specifications

Length: 15.4"

Base Length: 13.13"

Width: 3"

Height: 6.07"

Optional for

General

1/4″-20 Thread External Tooth Locknut, Zinc Nut for Tail Lights

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount TecNiq 8 Function 6" LED Tail Lights to all current Com-Fab Trailer models.

- Two of these are used with 1/4″- 20 Tail Light Bolts to mount Dry Launch SP7 Red Tail Lights to all Pre-2018 Com-Fab trailer models.

- One of these is used w/ 2-3/4"-20 Thread Bolts to secure PWT winch strap to crank winch.

MODEL: CFNUT1/4LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

5" x 1.25" x .25" Galvanized Flat Plate w/ 2 9/16" Holes and 3.5" Hole Centers

This item is part of these kits:

– Galvanized Winch Assembly Mounting Kit

– 2212G - Fender Mounting Kit (pre-April 2024 Models)

– 2212G - Bunk Mounting Kit

– Jon Boat Trailer Winch Assembly Mounting Kit

– Jon Boat Trailer Fender Mounting Kit

– Jon Boat Trailer Bow Support Mounting Kit

MODEL: CFFLTSTRPWNCHG

Used on

General

2 x 4 x 16′ Black Marine Carpeted Bunk Board

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

These are used for PT-1618, and PT-1820 trailer models.

MODEL: CFBUNKBRDC-16FT

Used on

General

15″ Galvanized Winch Assembly w/ RAM 600 lb Winch

This assembly includes a 15" Galvanized Winch Post, a RAM 600LB Capacity Crank Winch, a Winch Poly Bow Roller Assembly, and a Galvanized Winch Assembly Mounting Kit.

Mounting Hardware Includes:

4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts

MODEL: CFWNCHASSM-800G

Used on:

PWT-800G

General

RAM 600 lb Capacity Crank Winch w/ Mounting Kit

This item is a light duty winch with permanently lubricated bearings used for horizontal pulling applications. The item has a 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a RAM 600 lb Winch Handle. The mounting materials are sold separately.

Mounting Kit Includes:

2 - 3/8"-16 x 1" Zinc Hex Head Cap Bolt

2 - 3/8"-16 Serrated Zinc Flange Nuts

MODEL: CFWNCH600(RAM)

MPN: HWSP-600

Used on

General

Tandem Axle Galvanized Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

- This item is mounted to Pontoon Boat Trailer frames with a Pontoon Boat Trailer Tandem Axle Fender Mounting Kit, and it typically uses an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

- The hangers welded to bottom are for mounting two 2900 lb Idler Trailer Axles, or two 3500 lb Hydraulic Disc Brake Trailer Axles with a Pontoon Boat Trailer Tandem Axle Mounting Kit.

MODEL: CFFNDRPT(TA-G)

Used on

General

Galvanized Single Axle Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This fender with welded on spring hangers is mounted to a Pontoon Boat Trailer using a 2213G - Fender Mounting Kit, and typically uses a ST175/80R13 D Load Range 13″ Galv. Tire & Wheel. A 3500 lb Hydraulic Disc Brake Trailer Axle, or a 2900 lb Idler Trailer Axles is then mounted to the fender hangers using a Pontoon Boat Trailer Single Axle Mounting Kit.

MODEL: CFFNDRPT(SA-G)

Used on

General

4-Leaf Slipper Springs 1000 lb Maximum Capacity (Qty 2)

- This item is mounted to the 2000 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.

DEXTER MODEL: #13071

MODEL: CFAXLE-LSPRNG(4-SF)

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

2212G - Galvanized Fender with Front & Rear Sidemarker Lights

This fender is mounted to a PWT-2212G trailer model with a 2212G - Fender Mounting Kit, and fits a 4.80 x 12″ B Load Range Galvanized Tire & Wheel. It was updated for 2020 to accommodate side lighting.

MODEL: CFFNDR2212G-STEP

Used on

General

Model 66 Brake Hose Cover

This item attaches to Tie Down "Model 66" 6600 Lb Capacity Hydraulic Disc Brake Actuator w/ 2" Coupler to protect the Brake Hose. Comes with 2 Small Screws. 

MODEL: CFBRKECOVER

Used on

General

Aluminum E-Coat Caliper Assembly - Dexter

This item is a Tie Down/Dexter Aluminum E-Coat Caliper Assembly used on all Pontoon Boat Trailer models w/ Brakes prior to 2023 on 3500 lb Hydraulic Disc Brake Axles.

Materials Include

2 - 2" Pistons

2 - Brake Caliper Bleeder Valves

1 - Brass Elbow

2 - Organic Pads w/ Dacromet Backs. .

MODEL: CFAXLE-CALIPER(AL)

MPN: TDE 46304AP or Dexter 089-46304A

Used on (w/ Brakes, pre-2023)

General

Coupler Safety Pin - for TDE 660 & 850 Actuators

1/16-1/8IN 7x7x12.5 w/ 5/16 Safety Cable Pin. Used for Model TDE 660E and TDE 850E Actuators to Prevent Latch from Coming Undone

MODEL: CFCPLR-PIN

MPN: TDE 50301

General

Double PWC Trailer Fender Mounting Kit, Zinc-Plated - PWT-2213/4B Models

These are all of the requisite materials needed to mount a Black Powder Coated Fender 13″ Tire onto the PWT2213B, and PWT2214B trailer models.

Materials Include:

4 – 3/8″ Zinc Hex Flange Top Lock Nut

MODEL: CFFNDRKIT-PWT(DBL-PC)

Used on

General

35' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" Ring Terminal.

MODEL: CFWH35

Used on

General

3″ Amber Poly Bow Roller Bell End

This item is used as part of every Winch Assembly mounted on every PWT, and Jon Boat Trailer model.

This item is part of these assemblies:

- 3" Poly Bow Roller Assembly

- Winch Poly Bow Roller Assembly

MODEL: CFPOLYEBELL-3

MPN: TDE 48654

Used on

General

D.L. 1500LB Side Crank Swivel Jack

• Dutton-Lainson swivel marine tongue jack for boat and other trailer applications
• 1,500 lb. capacity
• 24-3/4" maximum tongue height
• Side wind handle with extra heavy screw drive and ergonomic handle grip
• Heavy duty polypropylene 8" diameter slotted wheel resists flat spots and cold weather cracking
• Zinc plated finish for additional rust resistance and longer life
• Easily swivels up for towing or down for stowing and locks in place in either position
• Reinforced wheel bracket for additional strength
• Includes all necessary bolt-on mounting hardware
• Made in the U.S.A.

Dutton-Lainson Model: 6850

MODEL: CFJACKSIDE-DL1500 (6850)

Used On

PT-/TT-2224
PT-/TT-2426

General

Pontoon Boat Trailer Tandem Axle Fender Mounting Kit

This kit contains all of the requisite materials needed to mount a Tandem Axle Galvanized Pontoon Boat Trailer Fender onto all Tandem Axle Pontoon Boat Trailer models.

Materials Include:

4 – 3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

4 – 6" x 1.5" x 1.25" Galvanized Flat Plate

8 – 3/8″ Galvanized Tri-Lock Hex Nuts

MODEL: CFFNDRKIT-PTG(TA)

Used on

General

Tie Down BATIE 190G Galvanized Tie Plate for 2" Square Axle Tubing (up to 2500lb Axles)

This item is part of the BATIE190G Galvanized Tie Plate Kit used to mount 5-Leaf Slipper Springs to 2500 lb Galvanized Trailer Axles. 

MODEL: CFAXLE-TIEPLATE(5-G)

MPN: 012-070-51 or 012-BATIE190G or BATIE190G

Specifications

Axle Size: 2" x 2" Square Axle

U-Bolt Size: 1/2"-13 x 2.06" x 4.31"

Dimensions: 4.49" x 3.5"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 9/16"

U-Bolt Finish: Galvanized

Plate Finish: Galvanized

Used on

General

7000# Galvanized Axle Tie Plate w/ 4.49" x 3.5" Dimensions for 2" Tubing and 1.75" Spring Width

This item is part of the 7000# Galvanized Tie Plate Kit used to mount Double Eye Leaf Springs on to 3500 lb Hydraulic Disc Brake Trailer Axles, 4250 lb Hydraulic Disc Brake Trailer Axles, or 2900 lb Idler Trailer Axles.

MODEL: CFAXLE-TIEPLATE(7000-G)

MPN: TDE 44849DG

Specifications

Axle Size: 2" x 2" Square Axle

U-Bolt Size: 1/2"-13 x 2.06" x 4.31"

Dimensions: 4.49" x 3.5"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 9/16"

U-Bolt Finish: Galvanized

Plate Finish: Galvanized

Used on

General

7/16" x 2.06" x 4.31" Galvanized U-Bolt

This item is part of the Kayak/Canoe Trailer Upright Mounting Kit.

MODEL: CFUBLT7/16x2.06x4.31G

MPN: TDE 84051G

Used on

KCT-1200
KCT-1400
KCT-1600

General

3/8"-16 x 1.56" x 3.63" U-Bolt, Zinc-Plated - For Standard 1.5" SQ Tubing Axles

This item is part of the Zinc Axle Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

MODEL: CFAXLE-UBLT(1.5SQ-Z)

MPN: TDE 83002-1Z

Used on