Parts

General

6" x 1.5" x .25" Galvanized Flat Plate w/ 2 7/16" Holes and 4.5" Hole Centers - Shackle Link

- This item is part of the 2213G - Fender Mounting Kit used to mount Fenders to PWT-2213G, and PWT-2214G Trailer models.

MODEL: CFFLTSTRPFNDR(DBL)G

Used on

General

3/8”-16 x 2.06” x 2.88” Zinc U-Bolt

This item is part of the 1000B - Bunk Mounting Kit used to mount bunks onto PWT-800B, PWT-1000B, AND PWT-1100B trailer models.

MODEL: CFUBLT3/8X2.88Z

Used on

General

Galvanized Single Axle Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This fender with welded on spring hangers is mounted to a Pontoon Boat Trailer using a 2213G - Fender Mounting Kit, and typically uses a ST175/80R13 D Load Range 13″ Galv. Tire & Wheel. A 3500 lb Hydraulic Disc Brake Trailer Axle, or a 2900 lb Idler Trailer Axles is then mounted to the fender hangers using a Pontoon Boat Trailer Single Axle Mounting Kit.

MODEL: CFFNDRPT(SA-G)

Used on

General

2212G - Galvanized Fender with Front & Rear Sidemarker Lights

This fender is mounted to a PWT-2212G trailer model with a 2212G - Fender Mounting Kit, and fits a 4.80 x 12″ B Load Range Galvanized Tire & Wheel. It was updated for 2020 to accommodate side lighting.

MODEL: CFFNDR2212G-STEP

Used on

General

3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Galvanized Tie Plate Kit used to mount 3-Leaf Slipper Springs to Galvanized 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002G

MODEL: CFAXLE-UBLT(1.5SQ-G)

Used on

General

2213/4B - Fender Mounting Kit

These are all of the requisite materials needed to mount a Black Powder Coated Fender 13″ Tire onto the PWT2213B, and PWT2214B trailer models.

Materials Include:

4 – 3/8″ Zinc Hex Flange Top Lock Nut

MODEL: CFFNDRKIT-2213B

Used on

General

2212B - Fender Mounting Kit

These are all of the requisite materials to mount a Black Powder Coated Fender 4.80 x 12" Tire onto a 2212B trailer model.

Materials Include:

4 – 3/8″ Zinc Hex Flange Top Lock Nut

MODEL: CFFNDRKIT-2212B

Used on

PWT-2212B

General

Tandem Axle Galvanized Pontoon Boat Trailer Fender with Welded-On Spring Hangers

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

- This item is mounted to Pontoon Boat Trailer frames with a Pontoon Boat Trailer Tandem Axle Fender Mounting Kit, and it typically uses an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

- The hangers welded to bottom are for mounting two 2900 lb Idler Trailer Axles, or two 3500 lb Hydraulic Disc Brake Trailer Axles with a Pontoon Boat Trailer Tandem Axle Mounting Kit.

MODEL: CFFNDRPT(TA-G)

Used on

General

2900 lb Galvanized Idler Trailer Axle w/ 545 Hubs and Springs

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 80.375" x 2" x 2" x .17" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Double Eye Springs (1850 lb)

1 - 7000# Galvanized Tie Plate Kit

- This item is used on all Tandem, and Single Axle Non-Brake Setup Pontoon Boat Trailers.

- It can be mounted to a Single Axle Pontoon Boat Trailer Fender with a Pontoon Boat Trailer Single Axle Mounting Kit.

- Two of them can be mounted to Tandem Axle Pontoon Boat Trailer Fenders with a Pontoon Boat Trailer Tandem Axle Mounting Kit

**Some states require brakes on all axles and/or wheels. please refer to local laws when placing your order. it is up to the individual dealer to stay within the guidelines as set by the legal authorities.

MODEL: CFAXLE2900G(IDLER)

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 2900 lb

Hub Face: 87"

Spring Center: 74"

Overall Length: 92"

Bearing Size: 1-3/8" x 1-1/16"

Optional for

General

Smooth Gloss Bengal Black Touch Up Pen

This item is used to touch up all of our Black Powder Coated Trailers, Fenders, and Winch Assemblies for sale. It is specifically designed for our trailers, and is an exact match finish. The instructions for use are clearly labeled on the back of the pen.

Specifications

Net Weight: 3.5 oz/9 ml

Exact Match Finish - Industrial. Product Contains less than 88% VOC/2.05 MIR

Contains: Acetone, Xylene, Toluene, and Petroleum Distillates.

DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR.

VAPORS MAY CAUSE FLASH FIRE.

VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, AND NOSE IRRITATION. 

NOTICE: Reports have associated repeated, and prolonged occupational overexposure to solvents with permanent brain, and nervous system damage. Intentional misuse by deliberately concentrating, and inhaling the contents may be harmful or fatal. WARNING! This product contains a chemical known to the state to California to cause cancer and birth defects or other reproductive harm. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120 Degrees Fahrenheit. Vapors may ignite explosively. Keep away from heat, sparks, and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe dust, vapors, or spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA approved) or leave the area. Close container after each use. Avoid contact with eyes, skin, and clothing. First Aid: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

Instructions

PREPARATION: Surface should be clean, dry, and free of wax, oil, rust, loose paint, etc. WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

DIRECTIONS: Shake well to get best color match. 

KEEP OUT OF THE REACH OF CHILDREN.

General

3/8"-16 x 1.56" x 3.63" Zinc U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Zinc Axle Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002Z

MODEL: CFAXLE-UBLT(1.5SQ-Z)

Used on

General

'River Hawk' Jon Boat Trailer Bunk Mounting Kit

This kit contains all of the requisite materials needed to mount a 2″ x 4″ x 10′ Black Marine Carpeted Bunk Board onto the JBT-1600 'River Hawk' Style Jon Boat Trailer model.

Materials Include:

3 – 3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt

3 – 8″ Adjustable Bolster Bunk Bracket

3 – 3/8″-16 x 1" Galvanized Hex Head Bolt

3 – Galvanized Angular Swivel Bracket

6 – 3/8″-16 Galvanized Tri-Lock Nut

9 – 3/8″-16 Galvanized Flat Washer

6 – 5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-JBT(HAWK)

Used on

JBT-1600 'River Hawk'

General

2 x 4 x 16′ Black Marine Carpeted Bunk Board

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

These are used for PT-1618, and PT-1820 trailer models.

MODEL: CFBUNKBRDC-16FT

Used on

General

Brass Banjo Brake Fitting Base

This item is used in conjunction with a banjo fitting bolt, a Black O-Ring and a Copper Washer for brake line quick connect.

For use with:

– Copper Banjo Fitting Washer

TIE DOWN MODEL: #11348

MODEL: CFBRKE-BASEBANJO

General

2000 lb Extended Galvanized PWC Trailer Axle w/ 545 Hubs and Springs

This item is not shipped. Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340.

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 84.45" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing 

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Slipper Springs (750 lb)

1 - Galvanized Tie Plate Kit

This item is mounted to the PWT-2212G trailer model with a Galvanized Axle Mounting Kit, and to the PWT-2212B trailer model with a Black Powder Coated Axle Mounting Kit

MODEL: CFAXLE2000G-EXTENDED

Specifications

Tubing: 1.5" Galvanized Square Axle

Load Rating: 2000 lb

Hub Face: 91.5"

Spring Center: 81.5"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

4-Leaf Slipper Springs 1000 lb Maximum Capacity (Qty 2)

- This item is mounted to the 2000 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.

DEXTER MODEL: #13071

MODEL: CFAXLE-LSPRNG(4-SF)

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

7/16" x 2.06" x 4.31" Galvanized U-Bolt

This item is part of the Kayak/Canoe Trailer Upright Mounting Kit.

TIE DOWN MODEL: #84051G

MODEL: CFUBLT7/16x2.06x4.31G

Used on

General

4" x 1" x .25" Zinc Flat Plate w/ 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the 1000B - Bunk Mounting Kit used to mount Bunk Boards onto PWT-800B, PWT-1000B, and PWT-1100B trailer models.

MODEL: CFFLTSTRPBUNK(SGL)Z

Used on

General

35' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" Ring Terminal.

MODEL: CFWH35

Used on

General

8.25" x1.5" x .25" Zinc Flat Plate w/ 7/16" Holes and a 3.5" Hole Center - Shackle Link

This item is part of the 2213B - Bunk Mounting Kit used to mount Bunk Boards onto 2213B, and 2214B trailer models.

MODEL: CFFLTSTRPBUNK(DBL)Z

Used on

 General

264″ Grey Poly Flex Hose Male-Banjo Brake Line - Dexter

This item is used as a brake line on PT-2426 models only.

For use with:

– Banjo Fitting Base
– Square Banjo Fitting Bolt
– Black O-Ring
– Copper Banjo Fitting Washer

TIE DOWN MODEL: #46223-264

MODEL: CFBRKELINE-264B(GREY)

Used on

PT-2426

General

10 ft Walk Board Black Marine Carpet

Protective carpeting for the 2″ x 8″ x 10′ Black Marine Carpeted Center Walk Board used on all of our Double PWC Trailer Models.

$2.25/ft in 100 ft rolls

If you are purchasing this carpet it needs to be a foot longer than the board itself.

Used on

General

Red Low Profile ID Light Bar w/ Ground Terminal

• Used on all Pontoon Trailer models
• Screws included with purchase
• Meets all FMVSS 108 requirements for wide and narrow vehicles
• IP68 Rated - Dust and water proof with hermetic seal
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Excellent UV Resistance - Automotive exterior lighting grade polycarbonate
• Reliable performance over 100,000 hours
• Can be mounted horizontal, vertical, or at any angle

TecNiq Model No. T10-RR00-1

MODEL: CFLIGHTBAR-LED(S-TEC)

Used On