Parts

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

Tie Down 7/16" Diameter x 2.593 Stainless Steel Slider Pin

This item is used for mounting a Tie Down caliper to a 9.6" vented rotor. Stainless steel caliper slide pins are easily accessible with hex heads for quick removal. It allows the caliper to float freely and insures proper alignment during installation. It fits all vented rotor calipers.

TIEDOWN MODEL #007-692-00 or 12114

MODEL: CFAXLE-PIN(CALIPER-SS)

Used on

General

ST175/80D13 C Load Range, 13″ Silver E-Coat Finish Tire & Wheel 50 psi - Kenda/Loadstar

This item is used on PWT-2213B, and PWT-2214B trailer models. Tire Capacity of 1360lbs (615kg). Speed rating of 81 mph. Max 50 PSI.

MODEL: CFT175DLRC-S

Used on

General

1000/1100G - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 6′ Carpeted Black Marine Bunk Board onto PWT-1000G trailer models, as well as a 2″ x 4″ x 7′ Black Marine Carpeted Bunk Board onto a PWT-1100G trailer model.

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-1000/1100G

Used on

General

Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly w/ Bearings, Seal, Amp, and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98" 

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- 12 Position Castle Nut

- Cotter Pin

MODEL: CFAXLE-HUB5BLT(1350-B)

Used on

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

23.5″ Pontoon Boat Trailer Guide Post Assembly

This assembly includes:

1 - 23.5″ Pontoon Guide Post, w/ 2″ x 4″ x 1′ carpeted wood bumpers

2 - 7/16" x 2.06" x 4.31" Galvanized U-Bolt

4 - 3/8″ Galvanized Flat Washer

4 - 7/16" Galvanized Tri-Lock Nut

MODEL: CFPOST-GUIDE(ASSM)

Used on

General

3/16" S-Hook with Latch Trailer Safety Chain - 48"

48" 2000 LB safety chain with 3/16 in S-Hooks and latch

MODEL: CFSFTYCHN

Used On

General

Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models

This fender is mounted to every Jon Boat Trailer, Kayak/Canoe Trailer and PWT-2212G models with a Jon Boat Trailer Fender Mounting Kit, and fits a 4.80 x 12″ C Load Range Galvanized Tire & Wheel.

MODEL: CFFNDRJBT/2212G

Used on

General

3-Leaf Slipper Springs 750 lb Maximum Capacity (Qty 2)

- This item is mounted to the 1500 lb Galvanized Trailer Axle, as well as the 1500 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.

- This item is mounted to the 1500 lb Black Powder Coated Trailer Axle with a Zinc Tie Plate Kit. 

TIE DOWN MODEL: #13087

MODEL: CFAXLE-LSPRNG(3-SF)

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

ST175/80R13 D Load Range 13″ Galvanized Tire & Wheel 65 psi

This item is used on our PT-2426, and PT-2628 Trailer Models, but is also an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFT175DLRD-G

Used on

Upgrade for

General

2213/4G - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 6′ Black Marine Carpeted Bunk Board onto a 2213G trailer model. The kit can also be used to mount a 2″ x 4″ x 7′ Black Marine Carpeted Bunk Board onto a 2214G trailer model.

Materials Include:

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-2213G

Used on

General

1200 lb Side Crank Swivel Jack

This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.

MAXIMUM CAPACITY: 1200LB

PACIDIC RIM MODEL: MJ-1200B

MODEL: CFJACKSIDE

Used on

General

Black Marine Carpet 10.25" Width

$2/ft in 100 ft rolls

- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.

If you are purchasing this carpet it needs to be a foot longer than the board itself.

This carpet comes in these specific sizes as well:

- 5 ft Bunk Board Black Marine Carpet

- 6 ft Bunk Board Black Marine Carpet

- 7 ft Bunk Board Black Marine Carpet

MODEL: CFBNKCOVER-CARPET(10.25)

Used on

Optional for

General

TecNiq Red LED V-Shaped Light Bar w/ 58" Lead

• Used on all Double PWT Trailer models.
• Screws included with purchase
• Fully submersible LED Identification bar
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Available in colored or clear impact resistant lens
• IP68 rating while exceeding FMVSS 108 standards
• Reliable performance over 100,000 hours

MODEL: CFLIGHTBAR-LED(V-TEC)

Used On

General

2 x 4 x 2′ Black Marine Carpeted Bow Support Bunk

This item is mounted with a Jon Boat Trailer Bow Support Bunk Mounting Kit to all Jon Boat Trailer models except the JBT-1600 'River Hawk'.

MODEL: CFBOWSPRTC-2FT

Used on

General

3" Poly Bow Roller Assembly

This is a section of the Winch Poly Bow Roller Assembly.

Materials Include:

1 – 3″ Poly Bow Roller 
2 – 3″ Poly Bow Roller Bell End
1 – 1/2″-13 x 4.5″ Zinc Bolt
2 – 1/2″ Zinc Flat Washer
1 – 1/2″-13 Top Lock Nut

MODEL: CFASSM-POLYRLR(3)

Used on

General

2500 lb Galvanized PWC Trailer Axle w/ 545 Hubs and Springs

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 83" x 2" x 2" x 3/16" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 5-Leaf Slipper Springs (1,250 lb)

1 - BATIE190G Tie Plate Kit

This item is mounted to the PWT-2213G, and PWT-2214G trailer models with a Galvanized Axle Mounting Kit.

MODEL: CFAXLE2500G

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 2500 lb

Hub Face: 93.5"

Spring Center: 83"

Overall Length: 98.5

Bearing Size: 1-1/16"

Used on

General

Dry Launch 60″ Red Triple Light Bar

This light bar can be mounted to all Double PWT, and Pontoon Boat Trailer models. It is secured with two 12 x 3/4″ Zinc Hex Washer Head Tek #3 Screws.

MODEL: CFLIGHTBAR-60

Optional for

General

2″ x 4″ x 7′ Black Marine Carpeted Bunk Board

These are used for all PWT-1100, and PWT-2214 trailer models.

1000B - Bunk Mounting Kit

1000G - Bunk Mounting Kit

2213B - Bunk Mounting Kit

2213G - Bunk Mounting Kit

MODEL: CFBUNKBRDC-7FT

Used on

General

Dry Launch Amber Side Marker Light w/ 10" of Wire

This item is a Dry Launch 203 Series with a snap out bulb slide. You can change the bulb without tools, and mount it with a single stud. It can be used as a Side Marker Light for the tongue of all Pontoon Boat Trailer models.

MODEL: CFLIGHTSDMRKR-10

Optional for

General

2213/4G - Galvanized Fender

This fender is mounted to a PWT-2213G, or PWT-2214G trailer model using a 2213G - Fender Mounting Kit, and fits an ST175/80D13 C Load Range 13″ Galvanized Tire & Wheel.

MODEL: CFFNDR2213

Used on

General

Zinc U Bolt Winch Assembly Mounting Kit for Black Powder Coated Trailers

This kit has all of the requisite materials needed to mount a Black Powder Coated Winch Assembly onto any Black Powder Coated PWT trailer model.

Materials Include:

2 – 3/8″-16 x 3" x 4.5″ Zinc U-Bolt

2 – 5" x 1.25" x .25" Zinc Flat Plate

4 – 3/8″-16 Zinc Plated Serrated Flange Nuts

MODEL: CFWNCHKIT-(PWC-Z)

Used on

General

17' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH16

Used on