Parts

General

3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt 

This item is a part of these kits:

- 2213G - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2212G - Fender Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Fender Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: #83027G

MODEL: CFUBLT3/8X2.38G

Used on

General

RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue

This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit

MODEL: CFCPLR(RAM)-3x2

Specifications

- Hole Diameter: 1/2"

- Hole Distance: 2 1/2"

- Hole Distance from Top: 7/8"

- Hole Distance from Base: 1"

Used on

General

Company Graphic for Single PWT and Jon Boat Trailers

This graphic sticks to the side of all Single PWT, Jon Boat, and PWT-2212 trailer models. 

Dimensions: 19.75" x 2"

MODEL: CFGRAPHIC-(3X1.5)

Used on

General

Galvanized Winch Assembly Mounting Kit

This kit contains all of the requisite materials needed to mount a Galvanized Winch Assembly onto all Galvanized PWT trailer models.

Materials Include:

2 – 3/8″ x 3.06" x 4.5″ Galvanized U-Bolt

2 – 5" x 1.25" x .25" Galvanized Flat Plate

4 – 3/8″ Galvanized USS Flat Washer

4 – 3/8″-16 Galvanized Tri-Lock Hex Nuts

MODEL: CFWNCHKITG

Used on

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

TecNiq Part No. S14-RRS1-1

MODEL: CFLIGHTSDMRKR-LED(TEC-R24)

Used on 

General

1500 lb Black Powder Coated PWC Trailer 545 Axle w/ Hubs and Springs

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 44.5" x 1.5" x 1.5" x 11 Gauge Black Powder Coated Axle Tubing 

2 - Black Powder Coated 5-Bolt Hub Assembly

2 - 3-Leaf Slipper Springs (750 lb)

1 - Zinc Tie Plate Kit

This item is mounted to the PWT-1000B, and the PWT-1100B with a Black Powder Coated Axle Mounting Kit.

MODEL: CFAXLE1500B

Specifications

Tubing: 1.5" Black Powder Coated Square Axle

Load Rating: 1500 lb

Hub Face: 50.5"

Spring Center: 41.19"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

1000 lb Galvanized PWC Trailer Axle w/ Hubs and Springs

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 44.5" x 1.5" x 1.5" x 11 Gauge Galvanized Axle Tubing 

2 - Galvanized 5-Bolt Hub Assembly

2 - 2-Leaf Slipper Spring (550 lb)

1 - Zinc Tie Plate Kit

This item is mounted to the PWT-800G, and all Jon Boat Trailer models with a Galvanized Axle Mounting Kit.

MODEL: CFAXLE1000G

Specifications

Tubing: 1.5" Galvanized Square Axle

Load Rating: 1000 lb

Hub Face: 50.5"

Spring Center: 41.188"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

1000/1100B - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 6′ Carpeted Black Marine Bunk Board onto PWT-1000B trailer models, as well as a 2″ x 4″ x 7′ Black Marine Carpeted Bunk Board onto a PWT-1100B trailer model.

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-1000B

Used on

General

Galvanized Angular Swivel Bracket - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B - Bunk Mounting Kit

- 1000G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B - Bunk Mounting Kit

- 2213G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

Used on

General

2213/4G - Fender Mounting Kit

This kit contains all of the requisite materials needed to mount a Galvanized Fender 13" Tire onto 2213G, 2214G, and Pre-2019 Single Axle Pontoon Boat Trailer models.

Materials Include:

2 – 3/8″-16 x 4.19″ x 3″ Galvanized U-Bolt

2 – 6" x 1.5" x 1.25" Galvanized Flat Plate

4 – 3/8″ Galvanized Tri-Lock Hex Nuts

MODEL: CFFNDRKITG-2213

Used on

General

21' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH21

Used on

JBT-1600 ‘RIVER HAWK’

General

2 x 4 x 10′ Black Marine Carpeted Bunk Board

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

These are used as the standard option for JBT-1600 'River Hawk' Trailer models, as well as an upgradeable option for the JBT-1400 model.

'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBUNKBRDC-10FT

Used on

General

ST175/80R13 D Load Range 13″ Aluminum Tire & Wheel 65 psi

This item is an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFTST175RLRD-VSPOKE

Upgrade for

General

2-Leaf Slipper Springs w/ Radius 550 lb Maximum Capacity (Qty 2)

This item is mounted to the 1000 lb Galvanized Trailer Axle, and the 1000 lb Black Powder Coated Trailer Axle using a Zinc Tie Plate Kit.

TIE DOWN MODEL: #13070

MODEL: CFAXLE2-LSPRNG(SL)

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

2213/4B - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2" x 4" x 6' Black Marine Carpeted Bunk Board onto a 2213B trailer model. This kit can also be used to mount a 2" x 4" x 7' Black Marine Carpeted Bunk Board onto a 2214B trailer model.

Materials Include:

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-2213B

Used on

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

2  x 4 x 5′ Black Marine Carpeted Bunk Board

These are used for PWT-800, and PWT-2212 trailer models.

Single PWC Zinc Bunk Mounting Kit

Single PWC Galvanized Bunk Mounting Kit

2212B - Bunk Mounting Kit

2212G - Bunk Mounting Kit

MODEL: CFBUNKBRDC-5FT

Used on

General

4.80 x 12″ AM02 Black Metal Machined Aluminum Tire & Wheel Load Range C, Bias

This is the tire and wheel used on the PWT1100AL model and optional for PWT-800, PWT-1000, PWT-1100, and PWT-2212 black powder coated and galvanized trailer models. Speed rating 81 mph.

MODEL: CFT48012-VSPOKE(BM)-LRC

Used on

PWT-1100AL

Optional for

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

Company Graphic for Double PWT and Pontoon Trailers

This graphic sticks to the side of all Double PWT and Pontoon Boat Trailer models.

Dimensions: 30.25" x 3"

MODEL: CFGRAPHIC-(4X2)

Used on

General

3/8"-16 x 2.06" x 2.88" Galvanized U-Bolt

This item is part of the 1000G Bunk Mounting Kit used to mount bunks to PWT-800G, PWT-1000G, AND PWT-1100G trailer models.

MODEL: CFUBLT3/8X2.88G

Used on

General

32″ Galvanized Winch Post

- This item is part of the 32″ Galvanized Winch Assembly which is mounted to the PWT-2213G, and PWT-2214G trailer models.

- This item is part of the 32" Galvanized Jon Boat Trailer Winch Assembly which is mounted every Jon Boat Trailer model.

MODEL: CFWNCHPOST32-G

Used on

General

Dutton-Lainson 980 Coupler 2" Class 2 (3,500 lb) Zinc Plated 3″ Wide Tongue

This item mounts to all PWT-2213, and PWT-2214 trailer models with a Coupler Mounting Kit.

MODEL: CFCPLR(DL)-980

Specifications

Hole Diameter: 1/2"

Hole Distance: 2 1/2"

Hole Distance from Top: 5/8"

Hole Distance from Base: 1"

Used on