Part

General

Model 66 6600 lb GVWR Capacity Hydraulic Disc Brake Actuator; 660 lb Tongue Load; 2″ Coupler (Includes Disc Brake Solenoid) - Dexter

This item is used with Hydraulic Disc Brake Setups on every Pontoon Boat Trailer model with Disc Brakes.This item is mounted to Pontoon Boat Trailer models with an Actuator Mounting Kit

MODEL: CFCPLR-BRAKE(DISC-660)

Used on

General

Tie Down 7/16" Diameter x 2.593 Stainless Steel Slider Pin

This item is used for mounting a Tie Down caliper to a 9.6" vented rotor. Stainless steel caliper slide pins are easily accessible with hex heads for quick removal. It allows the caliper to float freely and insures proper alignment during installation. It fits all vented rotor calipers.

TIEDOWN MODEL #007-692-00 or 12114

MODEL: CFAXLE-PIN(CALIPER-SS)

Used on

General

7/16" x 2.06" x 4.31" Galvanized U-Bolt

This item is part of the Kayak/Canoe Trailer Upright Mounting Kit.

TIE DOWN MODEL: #84051G

MODEL: CFUBLT7/16x2.06x4.31G

Used on

General

7000# Galvanized Axle Tie Plate w/ 4.49" x 3.5" Dimensions for 2" Tubing and 1.75" Spring Width

This item is part of the 7000# Galvanized Tie Plate Kit used to mount 3-Leaf Double Eye Springs on to 3500 lb Hydraulic Disc Brake Trailer Axles, or 2900 lb Idler Trailer Axles.

TIE DOWN MODEL: 44849DG

MODEL: CFAXLE-TIEPLATE(7000-G)

Specifications

Axle Size: 2" x 2" Square Axle

U-Bolt Size: 1/2"-13 x 2.06" x 4.31"

Dimensions: 4.49" x 3.5"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 9/16"

U-Bolt Finish: Galvanized

Plate Finish: Galvanized

Used on

General

7000# Zinc Axle Tie Plate w/ 4.49" x 3.5" Dimensions for 2" Tubing and 1.75" Spring Width

TIE DOWN MODEL: 44849DZ

MODEL: CFAXLE-TIEPLATE(7000-Z)

Specifications

Axle Size: 2" x 2" Square Axle

U-Bolt Size: 1/2"-13 x 2.06" x 4.31"

Dimensions: 4.49" x 3.5"

Tube Width: 2"

Spring Width: 1-3/4"

Hole Diameter: 9/16"

U-Bolt Finish: Zinc

Plate Finish: Zinc

General

8.25" x 1.5" x .25" Galvanized Flat Plate w/ 7/16" Holes and 3.5" Hole Centers - Shackle Link

This item is part of the 2213G - Bunk Board Mounting Kit used to mount Bunk Boards onto PWT-2213G, and PWT-2214G trailer models.

MODEL: CFFLTSTRPBUNK(DBL)G

Used on

General

8.25" x1.5" x .25" Zinc Flat Plate w/ 7/16" Holes and a 3.5" Hole Center - Shackle Link

This item is part of the 2213B - Bunk Mounting Kit used to mount Bunk Boards onto 2213B, and 2214B trailer models.

MODEL: CFFLTSTRPBUNK(DBL)Z

Used on

General

84″ Grey Flex Hose Banjo-Banjo Brake Line - Dexter

This item is used to connect two Aluminum E-Coat Caliper Assemblies on Tandem Axle Pontoon Boat Trailers. 

MODEL: CFBRKELINE-84BB(GREY)

Used on

General

8″ Galvanized Adjustable Bolster Bunk Bracket

This item is part of these kits:

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: 86130G

MODEL: CFBRKTBLSTR

Used on

General

Actuator Coupler Mounting Kit for 3" Wide Trailer Tongue

It is used to mount Actuators to all Pontoon Boat Trailer models w/ Brakes.

Materials Include:

3 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

3 - 1/2″-13 Top Lock Nut Zinc

MODEL: CFCPLRNUT/BLT-KIT-3

Used on

General

Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly w/ Bearings, Seal, Amp, and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98" 

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- 12 Position Castle Nut

- Cotter Pin

MODEL: CFAXLE-HUB5BLT(1350-B)

Used on

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

Tie Down Stainless Steel Caliper Bleeder Valve

This item is used on all TIE DOWN Aluminum E-Coat Caliper Assemblies. This item has a 1/8"-27 Stainless Steel Bleed Port.

TIE DOWN MODEL: #12114

MODEL: CFBRKE-BLEEDER

Used on

General

Brass Banjo Brake Fitting Base

This item is used in conjunction with a banjo fitting bolt, a Black O-Ring and a Copper Washer for brake line quick connect.

For use with:

– Copper Banjo Fitting Washer

TIE DOWN MODEL: #11348

MODEL: CFBRKE-BASEBANJO

General

Brass Banjo Fitting Bolt for (Round) Banjo-fitted Brake Lines

This item is used in conjunction with 64" Grey Flex Banjo-Banjo Brake Lines, O-Rings and Copper Banjo Fitting Washers to connect Aluminum E-Coat Caliber Assemblies on all tandem axle pontoon trailer models.

For use with: 

– Copper Banjo Fitting Washer

MODEL: CFBRKE-BLTBANJO(RD)

Used on

General

Company Graphic for Double PWT and Pontoon Trailers

This graphic sticks to the side of all Double PWT and Pontoon Boat Trailer models.

Dimensions: 30.25" x 3"

MODEL: CFGRAPHIC-(4X2)

Used on

General

Company Graphic for Single PWT and Jon Boat Trailers

This graphic sticks to the side of all Single PWT, Jon Boat, and PWT-2212 trailer models. 

Dimensions: 19.75" x 2"

MODEL: CFGRAPHIC-(3X1.5)

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

Coupler Safety Pin

1/16-1/8IN 7x7x12.5 w/ 5/16 Safety Cable Pin. Used for Model TDE 660E and TDE 850E Actuators to Prevent Latch from Coming Undone

MODEL: CFCPLR-PIN

General

Dutton Lainson 1400 lb Capacity Heavy Duty Winch

This item is a Dutton Lainson Heavy Duty Winch w/ 1400 lb capacity for horizontal pulling applications and 2 speeds.

Materials Included:

– 1/2″ Zinc Nylock Nut for RAM 600/1600 Winch Handle

MODEL: CFWNCH1400DL

Used on

General

Dry Launch 60″ Red Triple Light Bar

This light bar can be mounted to all Double PWT, and Pontoon Boat Trailer models. It is secured with two 12 x 3/4″ Zinc Hex Washer Head Tek #3 Screws.

MODEL: CFLIGHTBAR-60

Optional for

General

Dry Launch Amber Side Marker Light w/ 10" of Wire

This item is a Dry Launch 203 Series with a snap out bulb slide. You can change the bulb without tools, and mount it with a single stud. It can be used as a Side Marker Light for the tongue of all Pontoon Boat Trailer models.

MODEL: CFLIGHTSDMRKR-10

Optional for

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS