PWT-2212B Parts

General

Side Crank Swivel Jack Mounting Kit

This kit contains all of the  parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models

MODEL: CFJACK-MNTKIT

Used on

ALL COM-FAB TRAILER MODELS

General

3/8″-16 x 3.06" x 2.38″ Zinc U-Bolt

This item is part of these kits:

- 2213B - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212B - Fender Mounting Kit

TIEDOWN: 83027Z

MODEL: CFUBLT3/8X2.38Z

Used on

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

2  x 4 x 5′ Black Marine Carpeted Bunk Board

These are used for PWT-800, and PWT-2212 trailer models.

Single PWC Zinc Bunk Mounting Kit

Single PWC Galvanized Bunk Mounting Kit

2212B - Bunk Mounting Kit

2212G - Bunk Mounting Kit

MODEL: CFBUNKBRDC-5FT

Used on

General

2212B - Black Powder Coated Fender

This fender is mounted onto a Pre-2020 PWT-2212B trailer with a 2212B - Fender Mounting Kit, and fits a 4.80 x 12″ B Load Range Silver Tire & Wheel.

MODEL: CFFNDR2212B

Used on

PWT-2212B

General

Black Powder Coated Axle Mounting Kit

This kit is used to mount Black Powder Coated Axles to Black Powder Coated PWT Trailer models.

Materials Include: 

2 - 1/2" x 3" Zinc Hex Head Bolt

2 - 1/2"-13 Zinc Flange Top Lock Nut

MODEL: CFAXLEKIT-MOUNT(Z)

Used on

General

Company Graphic for Single PWT and Jon Boat Trailers

This graphic sticks to the side of all Single PWT, Jon Boat, and PWT-2212 trailer models. 

Dimensions: 19.75" x 2"

MODEL: CFGRAPHIC-(3X1.5)

Used on

General

Coupler Mounting Kit for 3" Wide Trailer Tongues

This item is used to mount Couplers to all trailer models without Brakes.

Materials Include: 

2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt

2 - 1/2″- 13 Zinc Top Lock Nut

MODEL: CFCPLR-MNTKIT(NONBRK)

Used on

ALL COM-FAB TRAILER MODELS

General

Black Marine Carpet 10.25" Width

$2/ft in 100 ft rolls

- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.

If you are purchasing this carpet it needs to be a foot longer than the board itself.

This carpet comes in these specific sizes as well:

- 5 ft Bunk Board Black Marine Carpet

- 6 ft Bunk Board Black Marine Carpet

- 7 ft Bunk Board Black Marine Carpet

MODEL: CFBNKCOVER-CARPET(10.25)

Used on

Optional for

General

3/8"-16 x 1.56" x 3.63" Zinc U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Zinc Axle Tie Plate Kit used to mount 2-Leaf Slipper Springs (550 lb), and 3-Leaf Slipper Springs (750 lb) to 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002Z

MODEL: CFAXLE-UBLT(1.5SQ-Z)

Used on

General

3/8"-16 x 1.56" x 3.63" Galvanized U-Bolt - For Standard 1.5" SQ Tubing Axles

This item is part of the Galvanized Tie Plate Kit used to mount 3-Leaf Slipper Springs to Galvanized 1.5" Square Axle Tubing.

TIE DOWN MODEL: #83002G

MODEL: CFAXLE-UBLT(1.5SQ-G)

Used on

General

3" Poly Bow Roller Assembly

This is a section of the Winch Poly Bow Roller Assembly.

Materials Include:

1 – 3″ Poly Bow Roller 
2 – 3″ Poly Bow Roller Bell End
1 – 1/2″-13 x 4.5″ Zinc Bolt
2 – 1/2″ Zinc Flat Washer
1 – 1/2″-13 Top Lock Nut

MODEL: CFASSM-POLYRLR(3)

Used on

General

2212B - Fender Mounting Kit

These are all of the requisite materials to mount a Black Powder Coated Fender 4.80 x 12" Tire onto a 2212B trailer model.

Materials Include:

4 – 3/8″ Zinc Hex Flange Top Lock Nut

MODEL: CFFNDRKIT-2212B

Used on

PWT-2212B

General

2212B - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 5′ Black Marine Carpeted Bunk Board onto a 2212B trailer model. 

Materials Include:

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-2212B

Used on

PWT-2212B

General

3/8″-16 x 1″ Zinc Hex Head Cap Bolt

This item is used with 3/8"-16 Serrated Zinc Flange Nuts to mount all crank winch models onto every type of winch post. It is also part of the 2213B - Bunk Mounting Kit used to mount bunks onto PWT-2213B, and PWT-2214B trailer models. 

MODEL: CFBLT3/8X1Z

Used on

ALL COM-FAB TRAILER MODELS

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

3/16" S-Hook with Latch Trailer Safety Chain - 48"

48" 2000 LB safety chain with 3/16 in S-Hooks and latch

MODEL: CFSFTYCHN

Used On

General

Smooth Gloss Bengal Black Spray Paint

This item is used to touch up all of our Black Powder Coated Trailers, Fenders, and Winch Assemblies for sale. It is specifically designed for our trailers, and is an exact match finish. The instructions for use are clearly labeled on the back of the can.

Specifications

Net Weight: 4.5oz/128g

Exact Match Finish - Industrial. Product Contains less than 88% VOC/2.05 MIR

Contains: Acetone and Petroleum Distillate

DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR.

VAPORS MAY CAUSE FLASH FIRE.

CONTENTS UNDER PRESSURE.

VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, AND NOSE IRRITATION. 

NOTICE: Reports have associated repeated, and prolonged occupational overexposure to solvents with permanent brain, and nervous system damage. Intentional misuse by deliberately concentrating, and inhaling the contents may be harmful or fatal. WARNING! This product contains a chemical known to the state to California to cause cancer and birth defects or other reproductive harm. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120 Degrees Fahrenheit. Vapors may ignite explosively. Keep away from heat, sparks, and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe dust, vapors, or spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA approved) or leave the area. Close container after each use. Avoid contact with eyes, skin, and clothing. First Aid: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

Instructions

PREPARATION: Surface should be clean, dry, and free of wax, oil, rust, loose paint, etc. WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

SHAKE CAN WELL BEFORE USING TO SPRAY: Hold 10 to 12 Inches from surface. Press valve down completely, moving spray. Allow paint to become tacky between coats. Light mist coats prevent runs or sags.

TO CLEAN VALVE: Invert can, press spray tip until a short spurt of clear gas escapes. Spray tip may be removed for cleaning, if necessary. Clean with a common pin and paint thinner.

KEEP OUT OF THE REACH OF CHILDREN.

General

Smooth Gloss Bengal Black Touch Up Pen

This item is used to touch up all of our Black Powder Coated Trailers, Fenders, and Winch Assemblies for sale. It is specifically designed for our trailers, and is an exact match finish. The instructions for use are clearly labeled on the back of the pen.

Specifications

Net Weight: 3.5 oz/9 ml

Exact Match Finish - Industrial. Product Contains less than 88% VOC/2.05 MIR

Contains: Acetone, Xylene, Toluene, and Petroleum Distillates.

DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR.

VAPORS MAY CAUSE FLASH FIRE.

VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, AND NOSE IRRITATION. 

NOTICE: Reports have associated repeated, and prolonged occupational overexposure to solvents with permanent brain, and nervous system damage. Intentional misuse by deliberately concentrating, and inhaling the contents may be harmful or fatal. WARNING! This product contains a chemical known to the state to California to cause cancer and birth defects or other reproductive harm. Do not puncture or incinerate (burn) container. Exposure to heat or prolonged exposure to sun may cause bursting. Do not expose to heat or store at temperatures above 120 Degrees Fahrenheit. Vapors may ignite explosively. Keep away from heat, sparks, and flame. Do not smoke. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe dust, vapors, or spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA approved) or leave the area. Close container after each use. Avoid contact with eyes, skin, and clothing. First Aid: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

Instructions

PREPARATION: Surface should be clean, dry, and free of wax, oil, rust, loose paint, etc. WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

DIRECTIONS: Shake well to get best color match. 

KEEP OUT OF THE REACH OF CHILDREN.

General

TecNiq Red LED V-Shaped Light Bar w/ 58" Lead

• Used on all Double PWT Trailer models.
• Screws included with purchase
• Fully submersible LED Identification bar
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Available in colored or clear impact resistant lens
• IP68 rating while exceeding FMVSS 108 standards
• Reliable performance over 100,000 hours

MODEL: CFLIGHTBAR-LED(V-TEC)

Used On

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

Triple Lip Grease Seal - 1.25" I.D. - 1.98"

This seal is part of our Galvanized 5-Bolt Hub Assembly, and our Black Powder Coated 5-Bolt Hub Assembly. This rubber coated seal fits Tiedown Bearings 44643, and 44649

TIEDOWN MODEL: 1252555UC

MODEL: CFAXLE-SEAL(TRIPLE-1.25)

Used on

General

TecNiq-S14 Amber LED Mini PC Side Marker Light with 24" Lead

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

Tecniq Part No. S14-AAS0-1

MODEL: CFLIGHTSDMRKR-LED(TEC-A24)

Used on 

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

TecNiq Part No. S14-RRS1-1

MODEL: CFLIGHTSDMRKR-LED(TEC-R24)

Used on