PWT-1000B Parts

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.

• Multi-Function 6" box tail light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(L)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq License Plate Bracket

TECNIQ MODEL: L95-0B00-1

MODEL: CFTAG-TEC

Used on

ALL COM-FAB TRAILER MODELS

General

2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub

This item is a part of all hub assemblies and comes as a pair.

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

TIE DOWN MODEL: #17093

MODEL: CFAXLE-CAP&PLUG

Used on

ALL COM-FAB TRAILER MODELS

General

17' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH16

Used on

General

Dutton-Lainson 900 lb Capacity Crank Winch

This item is a heavy duty winch used for horizontal pulling applications. It contains high carbon steel gears, permanently lubricated bearings, and a zinc tuffplate finish. A 12′ Winch Strap w/ Spring Loaded Hook and Loop End, and a Dutton-Lainson 900 lb Winch Handle. The mounting materials are sold separately.

Mounting Kit Includes:

2 - 3/8"-16 x 1" Zinc Hex Head Cap Bolt

2 - 3/8"-16 Serrated Zinc Flange Nuts

MODEL: CFWNCH900DL

Used on

General

3-Leaf Slipper Springs 750 lb Maximum Capacity (Qty 2)

- This item is mounted to the 1500 lb Galvanized Trailer Axle, as well as the 1500 lb Extended Galvanized Trailer Axle with a Galvanized Tie Plate Kit.

- This item is mounted to the 1500 lb Black Powder Coated Trailer Axle with a Zinc Tie Plate Kit. 

TIE DOWN MODEL: #13087

MODEL: CFAXLE-LSPRNG(3-SF)

Specifications

Length: 24.63"

Leaf Width: 1.75"

Arch Height: 4.50"

Bushing Type: Nylon

Used on

General

1200 lb Side Crank Swivel Jack

This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.

MAXIMUM CAPACITY: 1200LB

PACIDIC RIM MODEL: MJ-1200B

MODEL: CFJACKSIDE

Used on

General

RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue

This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit

MODEL: CFCPLR(RAM)-3x2

Specifications

- Hole Diameter: 1/2"

- Hole Distance: 2 1/2"

- Hole Distance from Top: 7/8"

- Hole Distance from Base: 1"

Used on

General

4.80 x 12″ C Load Range Silver E-Coat Finish Tire & Wheel, Bias - Kenda/Loadstar

This is the tire and wheel used on PWT-800B, PWT-1000B, PWT-1100B, and PWT-2212B black powder coated trailer models. Tire capacity is 990lbs (450kg). Speed rating 65 mph.

MODEL: CFT48012S-LRC

Used on

General

12′ Winch Strap w/ Spring Loaded Hook and Loop End

Strap is generally sold as a replacement part for the Dutton-Lainson 900 lb Capacity Crank Winch (CFWNCH900DL). If you have a Com-Fab PWC trailer this is the replacement strap for your trailer's winch. The strap has the following capabilities:

- Strap working load limit: 1,700 lbs

- Break strength: 2,600 lbs

- 12' Long strap with hook

- Hand saver loop dimensions: 1" x 18"

- Steel hook tensile strength: 3,750 lbs

- Mounting bolt dimensions: 2-1/2" x 1/4" bolt

MODEL: CFWNCHSTRAP-12FT(PWC)

Used on

General

Black Powder Coated 545 Bolt 1250/1350LB Hub Assembly w/ Bearings, Seal, Amp, and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98" 

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- 12 Position Castle Nut

- Cotter Pin

MODEL: CFAXLE-HUB5BLT(1350-B)

Used on

General

1500 lb Black Powder Coated PWC Trailer 545 Axle w/ Hubs and Springs

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 44.5" x 1.5" x 1.5" x 11 Gauge Black Powder Coated Axle Tubing 

2 - Black Powder Coated 5-Bolt Hub Assembly

2 - 3-Leaf Slipper Springs (750 lb)

1 - Zinc Tie Plate Kit

This item is mounted to the PWT-1000B, and the PWT-1100B with a Black Powder Coated Axle Mounting Kit.

MODEL: CFAXLE1500B

Specifications

Tubing: 1.5" Black Powder Coated Square Axle

Load Rating: 1500 lb

Hub Face: 50.5"

Spring Center: 41.19"

Overall Length: 56"

Bearing Size: 1-1/16"

Used on

General

Galvanized Angular Swivel Bracket - 7/16″ Top Hole

These are used to mount bunk boards onto all Jon Boat, and PWT Trailer models.

This item is part of these kits:

- 1000B - Bunk Mounting Kit

- 1000G - Bunk Mounting Kit

- 2212B - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2213B - Bunk Mounting Kit

- 2213G - Bunk Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBRKTSWIVEL

Used on

General

Winch Poly Bow Roller Assembly

This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model. 

Materials Include:

1 – Galvanized Bow Stop Bracket

1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt

1 – 3/8″-16 Zinc Hex Flange Top Lock Nut

1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt

1 – 1/2″-13 Zinc Top Lock Nut

1 – 3″ Amber Poly Bow Roller

2 – 3″ Amber Poly Bow Roller Bell End

2 – 1/2″- Zinc Flat Washer

MODEL: CFASSM-WNCHRLR(3)

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

2 x 4 x 6′ Carpeted Black Marine Bunk Board

These are used on PWT-1000, PWT-1100, PWT-2213, PWT-2214, and all Jon Boat Trailer models.

1000B - Bunk Mounting Kit

1000G - Bunk Mounting Kit

2213B - Bunk Mounting Kit

2213G - Bunk Mounting Kit

Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBUNKBRDC-6FT

Used on

General

1000/1100B - Bunk Mounting Kit

These are all of the requisite materials needed to mount a 2″ x 4″ x 6′ Carpeted Black Marine Bunk Board onto PWT-1000B trailer models, as well as a 2″ x 4″ x 7′ Black Marine Carpeted Bunk Board onto a PWT-1100B trailer model.

4 – 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBNKKIT-1000B

Used on

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

12 Position Castle Nut

This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.

TIE DOWN MODEL: #10634

MODEL: CFAXLE-NUT(CASTLE-L)

Used on