PT-2022 Parts

General

2900 lb Galvanized Idler Trailer Axle w/ 545 Hubs and Springs

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 80.375" x 2" x 2" x .17" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Double Eye Springs (1850 lb)

1 - 7000# Galvanized Tie Plate Kit

- This item is used on all Tandem, and Single Axle Non-Brake Setup Pontoon Boat Trailers.

- It can be mounted to a Single Axle Pontoon Boat Trailer Fender with a Pontoon Boat Trailer Single Axle Mounting Kit.

- Two of them can be mounted to Tandem Axle Pontoon Boat Trailer Fenders with a Pontoon Boat Trailer Tandem Axle Mounting Kit

**Some states require brakes on all axles and/or wheels. please refer to local laws when placing your order. it is up to the individual dealer to stay within the guidelines as set by the legal authorities.

MODEL: CFAXLE2900G(IDLER)

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 2900 lb

Hub Face: 87"

Spring Center: 74"

Overall Length: 92"

Bearing Size: 1-3/8" x 1-1/16"

Optional for

General

Axle Equalizer

Two of these axle equalizers are part of the Pontoon Boat Trailer Tandem Axle Mounting Kit used to mount 3-Leaf Double Eye Springs to frames on all Tandem Axle Setups for Pontoon Boat Trailers

MODEL: CFAXLE-EQUALIZER

Used on

General

Galvanized Side Mount Spare Tire Carrier

• This item is optional for all of our Galvanized Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The galvanized finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high. 

*Used on Galvanized Trailer Models Only

TIEDOWN MODEL: #86098

MODEL: CFSTB-SIDE(G)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL GALVANIZED TRAILER MODELS

General

2x2 Square Tubing Plug for 10-14 GA

This item is used on Pontoon Winch Stands & Canoe/Kayak Crossbars and Uprights. It may also be used in other applications utilizing 2" square tubing.

This item is part of these kits:

- 2 Capacity Canoe/Kayak Kit

- 3 Capacity Canoe/Kayak Kit

- 4 Capacity Canoe/Kayak Kit

- 2 Canoe + 2 Kayak Kit

- 6 Capacity Canoe/Kayak Kit

MODEL: CFCAP-2X2(10-14GA)

Used On

General

2x4 Rectangular Tubing Plug for 10-14 GA

This item is used on Pontoon Winch Stands and as End Caps to the 2x4 Tubing of Pontoon Trailers.

MODEL: CFCAP-2X4(10-14GA)

Used On

General

Dutton Lainson 1400 lb Capacity Heavy Duty Winch

This item is a Dutton Lainson Heavy Duty Winch w/ 1400 lb capacity for horizontal pulling applications and 2 speeds.

Materials Included:

– 1/2″ Zinc Nylock Nut for RAM 600/1600 Winch Handle

MODEL: CFWNCH1400DL

Used on

General

64″ Grey Flex Hose Banjo-Banjo Brake Line - Dexter

This item is used to connect two Aluminum E-Coat Caliper Assemblies on Tandem Axle Pontoon Boat Trailer models. 

For use with:

Used on

General

Weld Aid B-100 Brite Zinc Aerosol Spray Can

This product is used to touch up, and prevent rust and corrosion on all of our galvanized items for sale. The spray is 69% Zinc Metal ensuring that it matches the shine of any and all Hot-Dipped Galvanized Steel. It has a special no clog nozzle, and can cover up to 40 sq feet of steel. This item meets ASTM-A780 requirements for corrosion protection.

Read the Safety Instructions carefully before use of this item.

https://weldaid.com/wp-content/uploads/2018/11/1008302E.pdf

Specifications

Part No: B-100

UPC: 731592100013

Volume: 12.5 oz Primer

Model: CFGALVSPRAY

Used On

Heavy safety/breakaway chain for pontoon trailers. (1X) 1/4x31IN 5000LB Capacity Safety Chain w/ 7/16IN Hook & Latch, Grade 30

SKU: CFSFTYCHN-HVY

Used on all pontoon trailer models

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

TecNiq Part No. S14-RRS1-1

MODEL: CFLIGHTSDMRKR-LED(TEC-R24)

Used on 

General

Red Low Profile ID Light Bar w/ Ground Terminal

• Used on all Pontoon Trailer models
• Screws included with purchase
• Meets all FMVSS 108 requirements for wide and narrow vehicles
• IP68 Rated - Dust and water proof with hermetic seal
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Durable impact resistant lens
• Excellent UV Resistance - Automotive exterior lighting grade polycarbonate
• Reliable performance over 100,000 hours
• Can be mounted horizontal, vertical, or at any angle

TecNiq Model No. T10-RR00-1

MODEL: CFLIGHTBAR-LED(S-TEC)

Used On

General

Pontoon Trailer Winch Assembly Mounting Kit for 4"x3" Trailer Tongue

This kit contains all of the requisite materials needed to mount a Pontoon Winch Assembly onto all Galvanized Pontoon/Tritoon Trailer models

Materials Include: 

2 – 1/2"-13 x 3.06" x 5.31" Galvanized U-Bolts

2 – 1/2" SAE Galvanized Flat Washers

2 – 1/2"-13 Galvanized Tri-Lock Nuts

MODEL: CFWNCHKIT-(PT-G)

Used On

General

Black Powder Coated Side Mount Spare Tire Carrier

• This item is optional for all of our Black Powder Coated Trailer models.
• It can accommodate wheels from 10" to 16.5" with a spare tire.
• It fits all 4 and 5 lug wheels with 4" and 4.5" diameter hole patterns.
• The powder coated finish provides long lasting protection.
• The item can mount to trailer frames up to 3" wide and 4" high.
  

*Used on Black Powder Coated Trailer Models Only

TIEDOWN MODEL: #86100

MODEL: CFSTB-SIDE(B)

Installation Instructions

1. Using the spare tire carrier and spare tire as a guide, determine a suitable mounting location on trailer frame.

2. Slide U-bolt around the frame and through the holes in tire carrier.

3. Mount with flat washers, lock washers and nuts provided.

4. Using the spare tire to determine the correct holes to use, place the carriage bolts provided for mounting the spare tire in the holes of the rectangular plate. Bolt heads should be on the back side of the tire carrier. Secure bolts with “star” washers.

5. The mounting plate will accommodate several sizes of frames by using the various hole patterns.

6. Check position of the tire mount for proper clearance with the spare tire before tightening bolts.

7. Mount spare tire with 1/2" bolt, washers and hex nuts provided.

Optional for

ALL BLACK POWDER COATED TRAILER MODELS

General

Black Marine Carpet 10.25" Width

$2/ft in 100 ft rolls

- This carpet is used for bunks on all of our PWC Trailer, and Jon Boat Trailer models. It is optional for our Pontoon Trailer models and Canoe/Kayak Angler Kits.

If you are purchasing this carpet it needs to be a foot longer than the board itself.

This carpet comes in these specific sizes as well:

- 5 ft Bunk Board Black Marine Carpet

- 6 ft Bunk Board Black Marine Carpet

- 7 ft Bunk Board Black Marine Carpet

MODEL: CFBNKCOVER-CARPET(10.25)

Used on

Optional for

General

1200 lb Side Crank Swivel Jack

This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.

MAXIMUM CAPACITY: 1200LB

PACIDIC RIM MODEL: MJ-1200B

MODEL: CFJACKSIDE

Used on

General

Side Crank Swivel Jack Mounting Kit

This kit contains all of the  parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models

MODEL: CFJACK-MNTKIT

Used on

ALL COM-FAB TRAILER MODELS

General

ST175/80R13 D Load Range 13″ Aluminum Tire & Wheel 65 psi

This item is an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFTST175RLRD-VSPOKE

Upgrade for

Model DL2500A Winch with Heavy Duty Strap (25 ft.) Installed

General

Coupler Safety Pin

1/16-1/8IN 7x7x12.5 w/ 5/16 Safety Cable Pin. Used for Model TDE 660E and TDE 850E Actuators to Prevent Latch from Coming Undone

MODEL: CFCPLR-PIN

General

Galvanized Pontoon Winch Stand & Stair/Handrail Combo w/ D.L. 1400LB Capacity Crank Winch and Anti-slick Grip Stairs

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340

Used on

PT-1618

PT-1820

PT-2022

PT-2224

PT-2426

General

Black Marine Plastic 2IN X 4IN Wide 

$3.40/ft 

- This plastic is used for bunks on all of our Pontoon Trailer models.  It is optional for our Canoe/Kayak Angler Kits, PWC Trailer, and Jon Boat Trailer models. 

If you are purchasing this Plastic it needs to be a foot longer than the board itself.

MODEL: CFBNKCOVER-PLASTIC(4IN-CA)

Used on

PWT-2214G
JBT-900
JBT-1400
JBT-1600
JBT-1600 ‘RIVER HAWK