JBT-1600 'River Hawk' Parts

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

Used on

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

Optional for

ALL COM-FAB TRAILER MODELS

General

Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter

Hub Includes:

- Triple Lip Grease Seal - 1.25" I.D. - 1.98"

- 1-1/16" Bearing Cup

- 1-1/16" L44649 Bearings

- 1-1/2"-20 Lug Nut Studs

- 1/2″-20 Lug Nut (Set of 5)

- 1.98" Dust Cap

- Super Lube Rubber Grommet

- Cotter Pin

TIEDOWN MODEL: #46205X

MODEL: CFAXLE-HUB5BLT(1350-G)

Used on

General

2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub

This item is a part of all hub assemblies and comes as a pair.

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

TIE DOWN MODEL: #17093

MODEL: CFAXLE-CAP&PLUG

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq License Plate Bracket

TECNIQ MODEL: L95-0B00-1

MODEL: CFTAG-TEC

Used on

ALL COM-FAB TRAILER MODELS

General

1200 lb Side Crank Swivel Jack

This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.

MAXIMUM CAPACITY: 1200LB

PACIDIC RIM MODEL: MJ-1200B

MODEL: CFJACKSIDE

Used on

General

Winch Poly Bow Roller Assembly

This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model. 

Materials Include:

1 – Galvanized Bow Stop Bracket

1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt

1 – 3/8″-16 Zinc Hex Flange Top Lock Nut

1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt

1 – 1/2″-13 Zinc Top Lock Nut

1 – 3″ Amber Poly Bow Roller

2 – 3″ Amber Poly Bow Roller Bell End

2 – 1/2″- Zinc Flat Washer

MODEL: CFASSM-WNCHRLR(3)

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

Galvanized Axle Mounting Kit

This kit is used to mount Complete Galvanized Axles to all PWT, and Jon Boat Trailer models.

Materials Include: 

2 - 1/2" x 3" Galvanized Hex Head Bolt

2 - 1/2"-13 Galvanized Tri-Lock Nuts

MODEL: CFAXLEMNTKITG

Used on

General

3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt 

This item is a part of these kits:

- 2213G - Bunk Mounting Kit

- 2212G - Bunk Mounting Kit

- 2212G - Fender Mounting Kit

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Fender Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: #83027G

MODEL: CFUBLT3/8X2.38G

Used on

General

21' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.

MODEL: CFWH21

Used on

JBT-1600 ‘RIVER HAWK’

General

Galvanized Bow Stop Bracket

This item is part of the Winch Poly Bow Roller Assembly used on every type of winch stand for all Jon Boat, and PWT trailer models.

MODEL: CFBRKTWNCHRLR

Used on

General

12 Position Castle Nut

This item is fastened to the end of an Axle Spindle with the use of a 5/32" x 2" Zinc Plated Cotter Pin. This combination secures Hubs to all PWC Trailer Models. It is rated for axles less than 3000 lbs. It is a 1"-14 Thread 12-Slot Castle Nut to fit standard 1" trailer spindles.

TIE DOWN MODEL: #10634

MODEL: CFAXLE-NUT(CASTLE-L)

Used on

General

1-1/16" L44649 Bearings

These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs

UNIVERSAL MODEL: L44649

TIE DOWN MODEL: #11054

MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER

Used on

ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS

General

Jon Boat Trailer Winch Assembly Mounting Kit

This kit contains all of the requisite materials needed to mount a 32" Galvanized Winch Assembly w/DL 600 onto all Jon Boat Trailer models.

Materials Include:

2 – 3/8″ x 3.06" x 5.25″ Zinc U-Bolt

2 – 5" x 1.25" x .25" Galvanized Flat Plate

4 – 3/8″-16 Serrated Zinc Flange Nuts

MODEL: CFWNCHKIT-(JBT)

Used on

General

Side Crank Swivel Jack Mounting Kit

This kit contains all of the  parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models

MODEL: CFJACK-MNTKIT

Used on

ALL COM-FAB TRAILER MODELS

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

2 x 4 x 10′ Black Marine Carpeted Bunk Board

This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340 

These are used as the standard option for JBT-1600 'River Hawk' Trailer models, as well as an upgradeable option for the JBT-1400 model.

'River Hawk' Jon Boat Trailer Bunk Mounting Kit

MODEL: CFBUNKBRDC-10FT

Used on

General

8″ Galvanized Adjustable Bolster Bunk Bracket

This item is part of these kits:

- Jon Boat Trailer Bunk Mounting Kit

- Jon Boat Trailer Bow Support Mounting Kit

- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit

TIE DOWN MODEL: 86130G

MODEL: CFBRKTBLSTR

Used on

General

RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue

This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit

MODEL: CFCPLR(RAM)-3x2

Specifications

- Hole Diameter: 1/2"

- Hole Distance: 2 1/2"

- Hole Distance from Top: 7/8"

- Hole Distance from Base: 1"

Used on

General

Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models

This fender is mounted to every Jon Boat Trailer, Kayak/Canoe Trailer and PWT-2212G models with a Jon Boat Trailer Fender Mounting Kit, and fits a 4.80 x 12″ C Load Range Galvanized Tire & Wheel.

MODEL: CFFNDRJBT/2212G

Used on