JBT-1600 'River Hawk' Parts
Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent
$20.00
Brand Com-Fab
General
Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent
The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.
Dimensions: W = 6.75" H = 3.5" D = 2-1/4"
Materials Include:
2 - 1/4"-18 Zinc Nut
MODEL: CFLIGHTREAR(R)-INC(DL)
Optional for
ALL COM-FAB TRAILER MODELS
Locking Spare Tire Bracket, Fits 3″ Width Tubing
$19.99
Brand Com-Fab
General
Locking Spare Tire Bracket, fits 3″ Width Tubing
This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.
MODEL: CFSTB-TOP
Optional for
ALL COM-FAB TRAILER MODELS
TecNiq-T86 7 Function 6" LED Tail Light (Passenger Side)
$34.99 $24.00
Brand Com-Fab
General
TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail
- These are optional for all Trailer Models.
- Multi-Function 6" Box Tail Light
- Urethane Potting w/ Guaranteed Circuit Board Protection
- Dust and water proof with hermetic seal
- Durable impact resistant lens
- Meets all FMVSS 108 requirements for narrow and wide vehicles
- Reliable performance over 100,000 hours
- Fits standard mounting as a direct replacement
- Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
Rear Reflector, and License Plate Light (Left)
Includes two 7/16" bolts w/ nuts for mounting.
MODEL: CFLIGHTREAR(R)-LED(TEC)
Used on
ALL COM-FAB TRAILER MODELS
Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent
$20.00
Brand Com-Fab
General
Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent
The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.
Dimensions: W = 6.75" H = 3.5" D = 2-1/4"
Materials Include:
MODEL: CFLIGHTREAR(L)-INC(DL)
Optional for
ALL COM-FAB TRAILER MODELS
Galvanized 545 Bolt 1250/1350LB Hub Assembly - Dexter
$79.99 $69.99
Brand Com-Fab
General
Complete 545 Bolt 1250/1350LB Hub Assembly w/Bearings, Seal, Amp and Dust Cap - Dexter
Hub Includes:
- Triple Lip Grease Seal - 1.25" I.D. - 1.98"
- 1-1/16" Bearing Cup
- Cotter Pin
TIEDOWN MODEL: #46205X
MODEL: CFAXLE-HUB5BLT(1350-G)
Used on
2″ Steel Super Lube Grease Dust Cap & Plug Set (2x)
$9.99
Brand Com-Fab
General
2″ Steel Super Lube Grease Dust Cap & Plug for Axle Hub
This item is a part of all hub assemblies and comes as a pair.
Galvanized 5-Bolt Hub Assembly
Powder Coated Black 5-Bolt Hub Assembly
TIE DOWN MODEL: #17093
MODEL: CFAXLE-CAP&PLUG
Used on
ALL COM-FAB TRAILER MODELS
License Plate Bracket by TecNiq, black
$9.99 $2.00
Brand Com-Fab
General
TecNiq License Plate Bracket
TECNIQ MODEL: L95-0B00-1
MODEL: CFTAG-TEC
Used on
ALL COM-FAB TRAILER MODELS
1200 lb Side Crank Swivel Jack
$60.00
Brand Com-Fab
General
1200 lb Side Crank Swivel Jack
This item fits 3″ x 5“ tongues. It comes with a 1200 lb Side Crank Swivel Jack Mounting Kit.
MAXIMUM CAPACITY: 1200LB
PACIDIC RIM MODEL: MJ-1200B
MODEL: CFJACKSIDE
Used on
JBT-900
JBT-1400
JBT-1600
JBT-1600 ‘RIVER HAWK’
PT-1400 'MiniToon'
PT-1618
PT-1820
PT-2022
Winch Poly Bow Roller Assembly
$29.99
Brand Com-Fab
General
Winch Poly Bow Roller Assembly
This kit is part of every Winch Assembly used on every PWT, and Jon Boat Trailer model.
Materials Include:
1 – Galvanized Bow Stop Bracket
1 – 3/8″-16 x 3.75″ Zinc Hex Head Cap Bolt
1 – 3/8″-16 Zinc Hex Flange Top Lock Nut
1 – 1/2″-13 x 4.5″ Zinc Hex Head Cap Bolt
2 – 3″ Amber Poly Bow Roller Bell End
MODEL: CFASSM-WNCHRLR(3)
Used on
5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw
$0.70
Brand Com-Fab
General
5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw
It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.
MODEL: CFSCRWLAG-5/16-0150
Used on
ALL COM-FAB TRAILER MODELS
Galvanized Axle Mounting Kit
$8.99
Brand Com-Fab
General
Galvanized Axle Mounting Kit
This kit is used to mount Complete Galvanized Axles to all PWT, and Jon Boat Trailer models.
Materials Include:
2 - 1/2" x 3" Galvanized Hex Head Bolt
2 - 1/2"-13 Galvanized Tri-Lock Nuts
MODEL: CFAXLEMNTKITG
Used on
3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt
$5.99
Brand Com-Fab
General
3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt
This item is a part of these kits:
- Jon Boat Trailer Bunk Mounting Kit
- Jon Boat Trailer Fender Mounting Kit
- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit
TIE DOWN MODEL: #83027G
MODEL: CFUBLT3/8X2.38G
Used on
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
$18.00
Brand Com-Fab
General
21' 4-Pin Wire Harness Assembled w/ Protective Sleeve
The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" ring terminal.
MODEL: CFWH20
Used on
JBT-1600 ‘RIVER HAWK’
1-1/16" L44649 Bearings
$5.75
Brand Com-Fab
General
1-1/16" L44649 Bearings
These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs
UNIVERSAL MODEL: L44649
TIE DOWN MODEL: #11054
MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER
Used on
ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS
Jon Boat Trailer Winch Assembly Mounting Kit
$19.99
Brand Com-Fab
General
Jon Boat Trailer Winch Assembly Mounting Kit
This kit contains all of the requisite materials needed to mount a 32" Galvanized Winch Assembly w/DL 900 onto all Jon Boat Trailer models.
Materials Include:
2 – 3/8″ x 3.06" x 5.25″ Zinc U-Bolt
2 – 5" x 1.25" x .25" Galvanized Flat Plate
4 – 3/8″-16 Serrated Zinc Flange Nuts
MODEL: CFWNCHKIT-(JBT)
Used on
Side Crank Swivel Jack Mounting Kit for 1200/1500lb Jacks
$14.99
Brand Com-Fab
General
Side Crank Swivel Jack Mounting Kit
This kit contains all of the parts needed to mount the 1200 lb Side Crank Swivel Jack, as well as the 1500 lb Side Crank Swivel Jack to all trailer frame models
MODEL: CFJACK-MNTKIT
Used on
ALL COM-FAB TRAILER MODELS
1/2″-20 Lug Nut (Set of 5)
$7.50
Brand Com-Fab
General
1/2″-20 Lug Nut (Set of 5)
These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.
MODEL: CFNUTLUG
Used on
ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS
2 x 4 x 10′ Black Marine Carpeted Bunk Board
$59.99 $55.00
Brand Com-Fab
General
2 x 4 x 10′ Black Marine Carpeted Bunk Board
This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340
These are used as the standard option for JBT-1600 'River Hawk' Trailer models, as well as an upgradeable option for the JBT-1400 model.
'River Hawk' Jon Boat Trailer Bunk Mounting Kit
MODEL: CFBUNKBRDC-10FT
Used on
8″ Galvanized Adjustable Bolster Bunk Bracket
$7.99 $4.50
Brand Com-Fab
General
8″ Galvanized Adjustable Bolster Bunk Bracket
This item is part of these kits:
- Jon Boat Trailer Bunk Mounting Kit
- Jon Boat Trailer Bow Support Mounting Kit
- 'River Hawk' Jon Boat Trailer Bunk Mounting Kit
TIE DOWN MODEL: 86130G
MODEL: CFBRKTBLSTR
Used on
RAM Coupler 2" Ball for 3" Wide Trailer Tongue
$27.99
Brand Com-Fab
General
RAM 2″ (Class 2) Zinc Plated Coupler fits 3″ Wide Tongue
This item is mounted to PWT-800, PWT-1000, PWT-1100, PWT-2212, and all Jon Boat Trailer models with a Coupler Mounting Kit
MODEL: CFCPLR(RAM)-3x2
Specifications
- Hole Diameter: 1/2"
- Hole Distance: 2 1/2"
- Hole Distance from Top: 7/8"
- Hole Distance from Base: 1"
Used on
Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models
$74.99 $35.00
Brand Com-Fab
General
Galvanized Fender for Jon Boat, Canoe/Kayak Trailer and PWT-2212G Models
This fender is mounted to every Jon Boat Trailer, Kayak/Canoe Trailer and PWT-2212G models with a Jon Boat Trailer Fender Mounting Kit, and fits a 4.80 x 12″ C Load Range Galvanized Tire & Wheel.
MODEL: CFFNDRJBT/2212G
Used on
Jon Boat Trailer Fender Mounting Kit
$14.99
Brand Com-Fab
General
Jon Boat Trailer Fender Mounting Kit
These are all of the requisite materials needed to mount a Galvanized Fender 4.80 x 12” Tire onto every Jon Boat Trailer model.
Materials Include:
2 – 3/8″-16 x 3.06" x 2.38″ Galvanized U-Bolt
2 – 5" x 1.25" x .35" Galvanized Flat Plate
4 – 3/8" Galvanized Flat Washer
4 – 3/8" Galvanized Tri-Lock Nut
MODEL: CFFNDRKIT-JBT
Used on
Zinc Axle Tie Plate Kit for 1.5" Square Trailer Axle
$34.99 $32.99
Brand Com-Fab
General
Zinc Tie Plate Kit for 1.5" Square Trailer Axle
- This kit is used to mount springs 1.5" Square Trailer Axles.
- This kit is part of both 1000 lb Trailer Axles used on the PWT-800, and Jon Boat Trailer models.
-This kit is also part of the 1500 lb Black Powder Coated Trailer Axle used on the PWT-1000B, and the PWT-1100B.
Materials Include:
2 - Zinc Axle Tie Plate for 1.5" Square Trailer Axle
4 - 3/8"-16 x 1.56" x 3.63" Zinc U-Bolt
MODEL: CFAXLEKIT-SPRNGMNT(1.5K-Z)
Used on
Coupler Mounting Kit for 3" Wide Trailer Tongues
$7.99
Brand Com-Fab
General
Coupler Mounting Kit for 3" Wide Trailer Tongues
This item is used to mount Couplers to all trailer models without Brakes.
Materials Include:
2 - 1/2″-13 x 4″ Zinc Hex Head Cap Bolt
2 - 1/2″- 13 Zinc Top Lock Nut
MODEL: CFCPLR-MNTKIT(NONBRK)
Used on
ALL COM-FAB TRAILER MODELS