PT-2224 Parts

General

Dry Launch SP7 Red Tail Light (Passenger Side) - Incandescent

The Dry Launch submersible 7-function passenger side tail light is waterproof with a bulb slide that has built-in dust, and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″-18 Tail Light Bolt

2 - 1/4"-18 Zinc Nut

MODEL: CFLIGHTREAR(R)-INC(DL)

MPN: SP7RBX-99X1

Optional for

ALL COM-FAB TRAILER MODELS

General

Dry Launch SP7 Red Tail Light (Driver Side) - Incandescent

The Dry Launch submersible 8-function driver side tail light is waterproof with a bulb slide that has a built-in dust and splash guard. It snaps out for easy bulb replacement.

Dimensions:  W = 6"   H = 3.5"   D = 2-1/4"

Materials Include:

2 - 1/4″ - 18 Tail Light Bolt

2 - 1/4" -18 Zinc Nut

MODEL: CFLIGHTREAR(L)-INC(DL)

MPN: SP7RBX-99X1

Optional for

ALL COM-FAB TRAILER MODELS

General

ST175/80R13 13" D Load Range 545 Hole Pattern Galvanized Finish Radial Tire & Wheel - Kenda/Loadstar, 65 psi

This item is used on our PT-2426, and PT-2628 Trailer Models, but is also an upgradable option for all Trailer Models with 13" Tires. Speed rating is 81 mph.

MODEL: CFT175DLRD-G

Used on

Upgrade for

General

Locking Spare Tire Bracket, fits 3″ Width Tubing

This item is used to lock down, and transport a spare tire on all Com-Fab trailer models. Lock not included.

MODEL: CFSTB-TOP

Optional for

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86 7 Function 6" Box LED Passenger Side Tail Light w/ Pigtail

• These are optional for all Trailer Models.
• Multi-Function 6" Box Tail Light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(R)-LED(TEC)

MPN: T86-RR2RG-1

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq-T86-L 8 Function 8" Box Driver Side Tail Light w/ Pig Tail.

• Multi-Function 6" box tail light
• Urethane Potting w/ Guaranteed Circuit Board Protection
• Dust and water proof with hermetic seal
• Durable impact resistant lens
• Meets all FMVSS 108 requirements for narrow and wide vehicles
• Reliable performance over 100,000 hours
• Fits standard mounting as a direct replacement
• Functions include: Stop, Turn, Tail, Clearance, Side marker, Side Reflector,
  Rear Reflector, and License Plate Light (Left)

Includes two 7/16" bolts w/ nuts for mounting.

MODEL: CFLIGHTREAR(L)-LED(TEC)

MPN: T86-RR2LG-1

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq License Plate Bracket

MODEL: CFTAG-TEC

TECNIQ MODEL: L95-0B00-1

Used on

ALL COM-FAB TRAILER MODELS

General

TecNiq-S14 Amber LED Mini PC Side Marker Light with 24" Lead

• Comes with a 1/4" Nut.
• Brilliant illumination in a compact size
• IP 68 Rated - Dust and water proof
• TecSeal Urethane Potting - Guaranteed Circuit Board Protection
• Stud-mounted, no visible fasteners
• Reliable performance over 100,000 hours
• Vertical mount positions meets P2 specifications, while horizontal mount meets PC specifications 

MODEL: CFLIGHTSDMRKR-LED(TEC-A24)

MPN: S14-AAS0-1

Used on 

General

Model 660E 2" Ball 6600 lb GVWR Capacity Hydraulic Disc Brake Actuator Coupler; 660 lb Tongue Load (Includes Disc Brake Solenoid) - TDE/Dexter

This item is used with Hydraulic Disc Brake Setups on every Pontoon Boat Trailer model with Disc Brakes pre-February 2025. This item is mounted to Pontoon Boat Trailer models with an Actuator Mounting Kit

MODEL: CFCPLR-BRAKE(DISC-660)

Used on

General

2900 lb Idler Trailer Axle w/ 545 Hubs and Springs, Galvanized

*This item is not shipped! Pickup only from our location at 2375 Pleasantdale Rd. Atlanta, GA 30340*

*NOTE: if your trailer is older than 2006, call before ordering to ensure you receive the correct axle.*

Materials Include:

1 - 80.375" x 2" x 2" x .17" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Double Eye Springs (1850 lb)

1 - 7000# Galvanized Tie Plate Kit

- This item is used on all Tandem, and Single Axle Non-Brake Setup Pontoon Boat Trailers.

- It can be mounted to a Single Axle Pontoon Boat Trailer Fender with a Pontoon Boat Trailer Single Axle Mounting Kit.

- Two of them can be mounted to Tandem Axle Pontoon Boat Trailer Fenders with a Pontoon Boat Trailer Tandem Axle Mounting Kit

**Some states require brakes on all axles and/or wheels. please refer to local laws when placing your order. it is up to the individual dealer to stay within the guidelines as set by the legal authorities.

MODEL: CFAXLE2900G(IDLER)

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 2900 lb

Hub Face: 87"

Spring Center: 74"

Overall Length: 92"

Bearing Size: 1-3/8" x 1-1/16"

Optional for

General

ST175/80D13 13" C Load Range 545 Hole Pattern Galvanized Finish Bias Tire & Wheel - Kenda/Loadstar, 65 psi

This item is used on PWT-2213G, PWT-2214G, and our smaller Pontoon Boat Trailer models. Speed rating is 81 mph

MODEL: CFTST175DLRC-G

Used on

General

23.5″ Pontoon Boat Trailer Guide Post Assembly

This assembly includes:

1 - 23.5″ Pontoon Guide Post, w/ 2″ x 4″ x 1′ carpeted wood bumpers

2 - 7/16" x 2.06" x 4.31" Galvanized U-Bolt

4 - 3/8″ Galvanized Flat Washer

4 - 7/16" Galvanized Tri-Lock Nut

MODEL: CFPOST-GUIDE(ASSM)

Used on

General

35' 4-Pin Wire Harness Assembled w/ Protective Sleeve

The wiring is pulled through the trailer frame to provide connection between the lighting and the vehicle. It connects to the vehicle with a 4-Pin Male Connector. This item comes with a 3/8 20" Protective Sleeve and 30" Ground with 1/2" Ring Terminal.

MODEL: CFWH35

Used on

General

3500 lb Hydraulic Disc Brake Trailer Axle w/ Hubs and Springs, Galvanized

*This Item Is Not Shipped! Only Available For Local Pickup*

This item is used on all tandem, and single axle brake setup pontoon trailers.

Materials Include:

1 - 80.375" x 2" x 2" x .17" Gauge Galvanized Axle Tubing

2 - Galvanized 5-Bolt Hub Assembly

2 - 3-Leaf Double Eye Springs (1850 lb)

1 - 7000# Galvanized Tie Plate Kit

1 - Vented Rotor Disc Brake Kit

- It can be mounted to a Single Axle Pontoon Boat Trailer Fender with a Pontoon Boat Trailer Single Axle Mounting Kit.

- Two of them can be mounted to Tandem Axle Pontoon Boat Trailer Fenders with a Pontoon Boat Trailer Tandem Axle Mounting Kit

**Some states require brakes on all axles and/or wheels. please refer to local laws when placing your order. It is up to the individual dealer to stay within the guidelines as set by the legal authorities.

MODEL: CFAXLE3500G(DISC)-PT

Specifications

Tubing: 2" Galvanized Square Axle

Load Rating: 3500 lb

Hub Face: 87"

Spring Center: 74"

Overall Length: 92"

Bearing Size: 1-3/8" x 1-1/16"

Optional On

General

5/16″ x 1-1/2″ Galvanized Hex Head Lag Screw

It is used for mounting Bunk Boards to Galvanized Angular Swivel Brackets, and Pontoon Boat Trailer Bunk Brackets on all trailer models.

MODEL: CFSCRWLAG-5/16-0150

Used on

ALL COM-FAB TRAILER MODELS

General

4" x 1" x .25" Galvanized Flat Plate w/ 2 1/2" Holes and a 2.5" Hole Center - Shackle Link

- This item is part of the CFBNKKIT-PWT(SGL-G) to mount Bunk Boards onto PWT-800G, PWT-1000G, and PWT-1100G trailer models.

- This item is part of the Tall Galvanized Bunk Bracket Kit used to mount mount 2″ x 4″ or 2″ x 6″ bunk boards on all Pontoon Boat Trailer models.

MODEL: CFFLTSTRPBUNK(SGL)G

Used on

General

3/8"-16 Zinc Hex Flange Top Lock Nut Zinc

This item is part of the:

– 1000B - Bunk Mounting Kit

– 2212B - Fender Mounting Kit

– 2213B - Fender Mounting Kit

– Winch Poly Bow Roller Assembly

– Pontoon Boat Trailer Winch Assembly

MODEL: CFNUT3/8LOCKZ

Used on

ALL COM-FAB TRAILER MODELS

General

5/32" x 2" Cotter Pin, Zinc-Plated for Axle Spindle Hubs

It is used for fastening the Castle Nut to the Axle Spindle.

MODEL: CFAXLE-PIN(COTTER)

MPN: Dexter 019-10560

Used on

ALL COM-FAB TRAILER MODELS

General

3.06″ Wide Rubber Grommet for Steel E-Z Lube/SuperLube Grease Dust Cap

This item is used in conjunction with a 2" Dust Cap as part of both Hub Assemblies.

2″ Steel Super Lube Grease Dust Cap & Plug

Galvanized 5-Bolt Hub Assembly

Powder Coated Black 5-Bolt Hub Assembly

MODEL: CFAXLE-PLUG

MPN: Dexter 085-001-00 or TDE 46963

Used on

ALL COM-FAB TRAILER MODELS

General

1-1/16" L44649 Tapered Axle Bearings

These bearings fit a 1-1/16" diameter Spindle Shaft, and are used with L44610 Bearing Cups. These are used on Tie-Down #1350, and #1750 Hubs

MODEL: CFAXLE-BRG(1-1/16")-INNER/OUTER

UNIVERSAL MODEL: L44649

MPN: TDE 11054 or Dexter 031-031-02

Used on

ALL COM-FAB PWC, JON BOAT, AND CANOE/KAYAK TRAILER MODELS

General

1/2″-20 Lug Nut (Set of 5)

These are used for mounting tires on all trailer models to 1 1/2"-20 Threaded Stud.

MODEL: CFNUTLUG

Used on

ALL COM-FAB TRAILER MODELS WITH SILVER E-COAT OR GALVANIZED WHEELS

General

- Two of these are used with 1/4″ Zinc Nuts to mount TecNiq 8 Function 6" LED Tail Lights & TecNiq 7 Function 6" LED Tail Lights to all current Com-Fab Trailer Models

- Two of these are used with 1/4″ Zinc Nuts to mount Dry Launch Submersible Tail Lights to Pre-2018 Com-Fab trailer models.

MODEL: CFBLTLIGHT

Used On

ALL COM-FAB TRAILER MODELS

General

Brass Banjo Fitting Bolt for (Round) Banjo-fitted Brake Lines

This item is used in conjunction with 64" Grey Flex Banjo-Banjo Brake Lines, O-Rings and Copper Banjo Fitting Washers to connect Aluminum E-Coat Caliber Assemblies on all tandem axle pontoon trailer models.

For use with: 

– Copper Banjo Fitting Washer

MODEL: CFBRKE-BLTBANJO(RD)

Used on

General

Tall Galvanized Pontoon Boat Trailer Bunk Bracket Kit

This kit is a segment of what is used to mount bunk boards to all Pontoon Boat Trailer frames.

Materials Include:

1 - Tall Galvanized Pontoon Boat Trailer Bunk Bracket

1 - 3/8″-16 x 2.06″ x 5.25″ Zinc U-Bolt

1 - 4" x 1" x .25" Galvanized Flat Plate w/ 1/2" Holes

2 - 3/8"-16 Flange Top Lock Nut, Zinc

4 - 5/16" x 1-1/2″ Galvanized Hex Head Lag Screw

MODEL: CFBRKTPTBUNK(TALL)KIT

Used on